Questions tagged [utp]
For questions about Unshielded twisted pair (UTP) cabling, where it should always be in relation to networking in general.
66
questions
0
votes
2
answers
83
views
Is there a limit to the number of 10G copper SFP modules one can use in a switch?
I'm shopping for a new 10G ethernet switch for home, for copper ports.
The majority have SFP ports and lack RJ45 ports for copper. I understand this provides flexibility but I only need UTP/Copper to ...
0
votes
1
answer
87
views
UTP 6A cable with FTP 6A connector
Can I use cat. 6A FTP connector with cat. 6A UTP cable? I've already bought UTP cable but i cannot find 6A UTP connectors, only FTP. Will it work or will it generate some interferences?
0
votes
1
answer
65
views
What is an Ethernet Network Switch Port
I am trying to understand what an Ethernet Switch internally considers a single port.
My current understanding is that when a seller advertises an Ethernet Network Switch, like the one below, has five ...
2
votes
2
answers
126
views
Why is a PoE circuit limited to 328 feet?
I'm trying to learn about PoE and a friend told me the 100 meter limitation on a PoE circuit is because of the DC voltage drop on the power channel, not the data. I had understood the opposite, that ...
1
vote
1
answer
854
views
Does 10BASE-T contain four wire pairs or two-wire pairs and why is it if it's four wire pairs?
As far as I know, 10BASE-T and 100BASE-T (types of UTP) use two pairs of wires, while 1000BASE-T has four pairs of wires.
But when I look up the photo of 10BASE-T on google, it indeed contains four ...
1
vote
1
answer
179
views
Calculating stranded and solid cable length (for 22AWG)
Reading up on how to calculate cable lengths as a follow-up to my previous question, I understand that you have to use (102-H)/(1+D) to calculated the stranded length (C) and H+C to calculate the ...
1
vote
2
answers
635
views
Copper or Glass for Low Latency?
I'd like to preface the main content of this post with the following: I understand this question may be equally suited to the Physics Stack Exchange, and so I have posted on there as well, but maybe a ...
0
votes
1
answer
115
views
Multiple virtual UTP cables over one physical?
Say there is a physical UTP cable running from point A to point B.
At A there are two physically isolated devices, a1 and a2, each running their own network and unaware of each other's existence.
So ...
1
vote
1
answer
2k
views
UTP 1236 wiring [closed]
can someone tell why UTP 10/100 is wired 1236? why not 1234, 3456, 5678? (i know that on old adapters only 1236 pins were connected)
which was the rationale of 1236?
17
votes
5
answers
12k
views
How exactly does an Ethernet collision happen in the cable, since nodes use different circuits for Tx and Rx?
I am trying to understand how a collision occurs in Ethernet, especially when a duplex mismatch exists or when on a legacy Ethernet network two nodes transmit simultaneously.
Everyone explains the ...
3
votes
4
answers
1k
views
What is the difference between Ethernet types, considering bandwidth?
Different types of Ethernet (standard Ethernet, Fast Ethernet, Gigabit Ethernet) have different speed of data transfer (10 Mbit, 100 Mbit, 1 Gbit). Why is that?
On the physical layer, the speed of ...
4
votes
3
answers
2k
views
A reason why Ethernet has maximum cable length confuses me
The answer in this post suggests that it has two reasons.
While the impedance characteristics of a transmission line become less
favorable for high speed data as the line gets longer (resistance ...
22
votes
6
answers
11k
views
What is this thread-like material on this Cat6 U/UTP cable?
Does anyone know what this thread-like material to the right on the picture is?
Does it have anything to do with grounding?
It is a Cat6 U/UTP cable.
2
votes
1
answer
195
views
What type of Cat5e cable is this?
I am a fairly new networker and today I was terminating some cable at a gas station that is being built. The network cable that had been run from the gas pumps to the wiring closet confused the crap ...
0
votes
2
answers
602
views
How to avoid cable crosstalk?
I have 4 ADSL UTP cables.
How much distance do I need to leave between cables to avoid crosstalk?