All Questions
86
questions
0
votes
1
answer
213
views
How do layer 2 switches route based on MAC when daisy-chained?
Trying to think about this from a hardware design perspective, if I had to design an FPGA or a uC or something to manage a single port being the gateway port and one or more switched ports for routing,...
0
votes
0
answers
31
views
Why are connected switches not a good substitute for the network layer? [duplicate]
Unless I am missing something, because switches can be chained together, I am not sure why the network layer is needed. Theoretically, one can dedicate a frame to any MAC address, and assuming there ...
0
votes
3
answers
176
views
One layer 2 switch in the middle of router network
In general,
The connection should be like
PC---SW---ROUTER---Many ISP router---Router---SW---PC
so the packet will be from
layer 2 ---layer 3---layer 2
What if I put one layer 2 switch in the network
...
1
vote
4
answers
3k
views
Communication between different VLANs
In my previous understanding, there is no way to communicate between two VLANs using only layer 2.
After all, this is the purpose of having VLAN.
I found a forum that claims the following.
1.VLANs can ...
1
vote
1
answer
836
views
Can a switch fragment a jumbo frame?
In all resources seen that tackle the term of "jumbo frame", I understand that it is applied in a LAN, because:
It's a Jumbo frame, and a frame is for Layer 2
These resources talk a lot ...
8
votes
6
answers
5k
views
How Does A Layer 2 Switch Differentiate Between Different Networks?
I know that different IP-based networks can be connected to the same layer-2 switch. and I know each network's nodes can communicate just fine, however, no normal traffic can occur between two nodes ...
1
vote
1
answer
451
views
How FDB (Filtering Database) is filled out
I would like to understand what is used as a VLAN column in the FDB. For ACCESS port it is PVID if frame untagged or frame VID if frame is tagged, for TRUNK it is allowed VLANs?
We can represent the ...
0
votes
0
answers
29
views
Why collision domain occurs in hubs but not switches [duplicate]
if anyone knows the actual point and in depth answer to my question please help. the links in the comments didn't helped at all
Most of the websites which i saw are just vaguely saying that collision ...
0
votes
3
answers
2k
views
No internet access on VLAN
I'm trying to setup VLAN on my TL-SG3210 (3.0).
I created simple VLAN:
vlan 10
name "vlan10"
Then, I assigned port 2 & 3 to VLAN.
I also created interface:
interface vlan 10
ip ...
1
vote
0
answers
78
views
What are non-learning and learning VLANs?
I was going through some IEEE standards for switches (IEEE 802.1aq and IEEE 802.1Qca), and came upon a terminology of learning and non-learning VLANs.
I read that learning VLANs are used in Shortest ...
0
votes
2
answers
455
views
How do layer-2 devices (bridges/switches) join a multicast MAC address?
I was going through the IEEE 802.1Q (2018) standard on my own. The standard speaks about group addresses, and how these group addresses are learned by transit bridges, which is all fine.
But how do ...
1
vote
2
answers
291
views
Proxy-ARP when the destination device is connected to the same layer-2 switch, but belongs to a different subnet
I have recently learned about Proxy-ARP and am slightly confused about what would happen in the following scenario. Let's say I have two host devices A (IP: 10.0.0.10/24) and B (IP: 10.0.1.10/24) that ...
6
votes
2
answers
4k
views
How do I know the switch is layer 2 or layer 3?
Is it possible to find the switch is Layer3 or Layer2 in (Switch)CLI? Is there any command to check whether the switch Layer(Layer 3 or 2) in CLI?
0
votes
1
answer
35
views
Where can I find virtual switches to learn about layer 2 [closed]
I am learning about layer 2 networking, arp, cam tables, mac addresses etc. I will like to see some of these things in action but I do not have access to physical hardware now, does anyone know of a ...
1
vote
2
answers
306
views
How does an L3 Supported Switch differentiate L2/L3 Packets?
I had a managed or layer 3 supported switch (it can process both layer 2 and layer 3 packets). Now a packet from a connected host comes to it, sending traffic. How does the switch decide to process it ...