Questions tagged [brocade]
A tag for questions involving Brocade Communications Systems hardware or software.
65
questions
1
vote
2
answers
594
views
Brocade 7450 - set MTU to 9000
I have brocade icx 7450.
I already enabled jumbo frames to increase MTU packets on switch.
But unfortunately I am not able to change MTU size of port which I want. When typing after choosing interface ...
0
votes
1
answer
533
views
Unable to delete zones in the effective configuration
I was given the task of zoning and mistakenly I created new cfg and did zoning of a host. Now I am trying to delete zoning using below steps:
Zonedelete
Cfgsave cfgenable
Cfgremove
Cfgsave cfgenable
...
0
votes
2
answers
96
views
Brocade SX800 Management Problem
In my company we have a brocade sx800 backbone SW, it is not used for 4 years. Now we need it for new warehouse project.But we don't know what was the ip addresses and no info about this device. When ...
2
votes
2
answers
4k
views
How to populate ARP table without having to ping every device individually through the console on a Brocade ICX 7750 switch
I need to make a port-IP diagram and so far the best way to do this seems to be through show arp after consoling into the brocade switch. The arp table is empty however, and the only way I have been ...
0
votes
1
answer
69
views
Network speeds severely impacted by latency [closed]
I'm troubleshooting a situation where clients in far off locations with high latency connections to our network are experiencing severely adverse network transfer speeds.
If I run a speed test from ...
0
votes
1
answer
246
views
Is it possible to assign an IP to a tagged dual-mode port (Brocade)
I have a router (ubiquity USG) and a Brocade FCX648 Layer 3 switch. (I have a second one in a stack, but that's unrelated). The end goal is to be able to connect the switch to my router, provide IPs ...
0
votes
1
answer
680
views
Capture traffic flowing through a Brocade switch remotely
I am currently doing packet capture through mirroring with Wireshark as mentioned in this post
I can mirror the traffic to a port physically jacked into and analyze the packets redirected there w/ ...
1
vote
1
answer
92
views
Brocade OSPFv3 Routes are not installed
I am trying to deploy OSPFv3 across our network. However a few routers do not install the OSPFv3 route's to their routing tables. For example, this router is able to ping a certain host on the network....
2
votes
1
answer
194
views
Brocade L2VPN Route Reflector
I am trying to create an MPLS VPLS network where the VPLS instances are auto-discovered via BGP L2VPN. The issue I'm currently facing is that the routes are not reflected and there seems to be no ...
0
votes
1
answer
577
views
Brocade/Ruckus per vlan spanning tree vs Cisco
Brocade = (config-vlan-10)#spanning-tree rstp
This seems to enable rstp per vlan. This example enabling it on vlan 10.
Cisco = spanning-tree mode rapid-pvst
This enables Rapid PVST+ under the covers ...
0
votes
1
answer
457
views
802.1x Multiple Devices
I'm in the process of implementing wired 802.1x. I've been testing with HP 2530 switches and everything seems to work okay enough. On a different site I use Brocade (now Ruckus) 6450 switches. I ...
0
votes
0
answers
122
views
Brocade XMR randomly losing virtual interface IP address
We have a pair of XMR routers configured 100+ VLANs running VSRP downstream and BGP upstream. At random times, the IP information is deleted and I have to go in and reset it.
Each VLAN config looks ...
0
votes
1
answer
17k
views
Brocade smooth reboot command
I am newbie regarding switches.
I have Brocade ICX 7250 and 7450.
I would like to know, what is the command for smooth reboot of switch. I do not want to unplug power cable and lost configuration.
I ...
4
votes
1
answer
1k
views
Cross datacenter IP failover/migration
I am trying to wrap my head around this (very) simple issue of IP failover from one physical location to another. I have a few Virtual machines running at Site A where I need to rebuild the NAS. In ...
1
vote
1
answer
1k
views
out-of-band interface vs normal interface in switches (cisco, brocade,...)
i have a question abou out of band management interface in cisco and brocade switches, for example we can set 192.168.1.0/29 on our switches oob then via our lan we can access the switch in case of ...