Questions tagged [surface-preparation]
The surface-preparation tag has no usage guidance.
15
questions
0
votes
0
answers
31
views
Legend or not: wood coat should "breath"?
I am going to stain some pine boards, then coat them with boiled linseed oil. The latter should let moisture to diffuse through (correct me if I am wrong), but the water-based stain produces poorly ...
0
votes
0
answers
52
views
Grade C surface plate
Surface plates come in three grades: AA, A and B. The AA grade has the best flatness, while grades A and B have respectively 2 and 4 times less accuracy. Grade B is still much flatter than normal ...
1
vote
0
answers
32
views
Can anyone suggest an Economical way for Polishing wound Wires?
I am working as a mechanical design engineer. At my work place, we were making chairs with 12 mm diameter wire via bending. We were using mild steel flash wires which was like the perfect wire with ...
0
votes
3
answers
721
views
Conventions regarding sliding and press-fit tolerances for shafts and bearings
I often build things (3D printers, skateboard wheels, bicycle parts) that use off-the-shelf ball-bearings. These ball bearings are available in nominal mm sizes, and to the limit of my measuring tools,...
1
vote
0
answers
51
views
How is EPD different / related to anodising?
What is the process of applying dye to anodized surfaces (specifically aluminum)?
Is electrophoretic deposition (EPD) just the process used to apply the dye to anodised surfaces?
Or is it a ...
0
votes
1
answer
46
views
Engineering standards or testing standards for hot punched metal holes for rolled steel
So, I have a problem with fatigue cracking originating from hot punched holes. From failure forensic reviews, it seems like surface conditions contributed to some of the failures, especially where ...
0
votes
3
answers
946
views
Surface Finish and Strength
Does surface finish affect steels strength properties? If so, how does strength increase or decrease with the type of surface finish applied?
3
votes
4
answers
2k
views
How land is made flat at scale
For building something like a big building or a parking garage, there is a need for a large flat surface of concrete. Wondering how they make the dirt and the concrete flat. It's hard to make a tiny ...
0
votes
2
answers
299
views
Would it be possible to put an anti-condensation coating on, say, an ice bag such that it will not get wet in use?
I have seen anti-condensation coatings for glass, but as far as I know they're designed to cause any moisture that does form on them to sheet rather than bead. They do not, however, actually prevent ...
4
votes
1
answer
402
views
In what cases are the roughness values Rt and Ra used?
Roughness measurement instruments output those two values, where Rt is the distance between the top of the highest peak and the bottom of the lowest valley, and Ra is the average distance of every ...
1
vote
1
answer
37
views
How to avoid oxidation of Si using a sub nanometer layer
Which material can be used to protect a Si layer from Oxidation by a sub nanometer layer?
3
votes
1
answer
3k
views
How to do gold plating on Anodized aluminum and stainless steel?
I have done some research and asked in a few forums for gold plating on anodized aluminum and stainless steel but haven't yet found the answer to my questions.
What are the chemicals for pre-...
4
votes
1
answer
237
views
How can I get a quick 2B shine on grade 316 stainless steel?
I have a stainless steel (316) 2B finish strip. I tried buffing the material for a shiny surface but it takes lot of time to finish my production. So, I want to know if there is any chemical ...
6
votes
2
answers
1k
views
Cleaning anodised aluminium
We have some metal parts in our machines, which are anodised aluminium. Those machines are due to be shipped to the customer in the near future, but I have noticed some pitting or slight rust ...
2
votes
2
answers
174
views
Buffing/Polishing bulk Aluminum
I'm buffing the years of built up dirt off a aluminum grain tipper trailer, using a woolen buffing pad mounted on a angle grinder. I'm going in a upwards & downwards motion with great success, ...