Questions tagged [structural-engineering]
Questions related to the integrity, design requirements, or analysis of structures.
1,348
questions
0
votes
0
answers
24
views
What does the inside of an external wall look like?
I want to be able to simulate heat transfer through a wall, and to do that I need to know what the anatomy of the wall I'm simulating is. Preferably be simple e.g 1/2 inch ply wood to 4 in of fiber ...
0
votes
0
answers
20
views
Which Timber LOK screws to reinforce shallow ridge, and how many?
I bought a tiny house shell that still needs some rafter reinforcement. I have chevron-shaped gussets from 1/2'' plywood that I'm going to glue and nail on either side of the middle gambrel joint on ...
0
votes
0
answers
13
views
How to model fibre reinforced concrete on LUSAS?
As part of my dissertation, I need to cross verify my finite element analysis results using LUSAS using some experimental results, and although i can find some stress-strain relation in some articles, ...
0
votes
1
answer
38
views
Design a string
Consider a string with a mass attached. The string is fixed to the support above, and the mass is hanged at the other end. Is it possible to design the string for the following two cases?
The mass is ...
0
votes
1
answer
32
views
Tipping Point for Free Standing Wall
I work at a museum and we use weighted free standing walls to hang artwork in the center of rooms.
Could someone recommend how much weight to use inside our walls to ensure stability with the ...
0
votes
1
answer
17
views
Glue type for HDPE
What type of glue should be used for HDPE sheet to glue to itself
And what type of glue for HDPE be glued to wood?
0
votes
1
answer
21
views
Find out the loads acting per unit length on the beams supporting an open well stair
Please see the attached picture.
I want to find out the dead load per unit length and live load per unit length (both in kN/m), that will be acting on the floor beam (300 mm × 450 mm) and the landing ...
0
votes
0
answers
20
views
King post truss question
Problem:
Sagging roof in the middle of a garage.
I could sister the bottom cord and/or add struts from bottom cord to the rafters but room is very limited.
Question:
After jacking the trusses at the ...
0
votes
0
answers
12
views
Framing material for a pickup bed topper for overlanding
and thanks in advance for your comments. I am looking for a light weight framing solution, for a diy truck bed topper to use while overlanding.
The frame needs to hold about 300lbs dynamic load while ...
0
votes
1
answer
26
views
Are mutli-story structure slabs poured on-center?
What exactly does it mean to have a multi-storey building where each storey is 2.4 meters?
I've read a lot of descriptions of buildings that say each storey is "2.4 meters" or "3 meters&...
0
votes
1
answer
31
views
Why do period and damping ratio affect acceleration?
In the table above, the period of the structure $(T)$, the acceleration coefficient on the structure ($g$ in terms of gravitational acceleration) $Sa(T)$, The damping ratio is expressed as $ζ$ .
As ...
0
votes
1
answer
29
views
How does one calculate the aerodynamic pressure on a spacecraft during Max Q?
Just as lift - off of a spacecraft commences, that spacecraft undergoes aerodynamic pressure. After a certain point, the spacecraft reaches Max Q or maximum aerodynamic pressure. I do know that Max Q ...
0
votes
2
answers
42
views
Steel beam splice design
What is a good source of design recomendations for beam splices? I'm designing a structure and I need some help with getting proper splice strength for certain beam size. To make it simpler, I need ...
0
votes
1
answer
33
views
Names for 3d tensile structure
A naive natural language description might be 'pole supported by tent-like 3d wire net' for the depicted playground climbing arrangement made of rope with a pole in the center.
Is there a more precise ...
0
votes
0
answers
64
views
How to calculate the material and thickness I need for a certain force on it?
I am trying to figure out how to design how thick a material has to be so that the bar shown in picture 1 stays intact when a user is running on it.
Background: The project is a treadmill and the user ...