Skip to main content

Questions tagged [generator]

The tag has no usage guidance.

0 votes
0 answers
17 views

Does an array of Peltier module need a diode between each module?

I have a bunch of Peltier module that I wish to connect in series/parallel and use them as a thermopile generator. However I was wondering if its necessary to attach a diode between each module to ...
Philip C's user avatar
0 votes
1 answer
22 views

Can this new AC motor/generator design work?

I'm currently in the works of developing a vertically suspended flywheel, and I'm trying to figure out the best method to convert rotational energy to electrical energy and vice versa. I don't want to ...
ARJ's user avatar
  • 105
3 votes
1 answer
82 views

What's the smallest possible nuclear power generator?

Nuclear microreactors like Westinghouse's eVinci are small enough to fit on a flatbed semi-truck, and NuScale Power's small modular reactor (SMR) is relatively small, too; but are there smaller ...
Geremia's user avatar
  • 407
0 votes
0 answers
18 views

High temperature in seal oil vacuum pump (not in the bearing), steam power plant. Why the seal oil vacuum pump suddenly increased in temperature?

Seal oil vacuum pump in steam power plant, suddenly have temperature increased, it's in the pump's body, not in the bearing. Why is that happen? I noticed that temperature of main seal oil tank in ...
Ferdiansyah Zhultriza's user avatar
1 vote
0 answers
50 views

Electric motors and Internal Combustion Engines compared

I know that Internal Combustion engines are rated in terms of peak power developed, while electric motors are generally specified in terms of continuous power output. Is there a good way to determine ...
Slartibartfast's user avatar
0 votes
1 answer
31 views

Impact of generator start-up on its health

In this paper, the authors state that the wear effect of a genset star-up is comparable to the wear cause by 1 to 4 minutes running at full load. This paper dates from 1993, I am looking for a more ...
genset123's user avatar
0 votes
1 answer
104 views

Why does a car generator employs an alternator (i.e. AC) when power supply is provided by a battery (i.e. DC)?

An alternator generates AC current, whereas batteries (as far as I know) provide/are charged with DC current. So I'm wondering, how is this apparent mismatch explained? Do car manufacturers employ a ...
temporary_pigeon's user avatar
0 votes
1 answer
37 views

Can flow batteries be optimized to be fed low voltage and high current?

Can flow batteries be optimized to be fed low voltage and high current (such as from a homopolar generator, and then feed a local consumer power grid)?
Mark Besser's user avatar
1 vote
1 answer
89 views

What device/system would be used to increase rpm and decrease torque of some shaft?

As posed above... (sorry if not asked correctly - my first time on SE)
Again's user avatar
  • 13
0 votes
1 answer
40 views

How to match a synchronous generator with a powered shaft?

Given is a shaft powered by a steam turbine that rotates unloaded (i.e without generator) at $ \omega $ rad/s and a torque of $T$ Nm. How would one match a generator to extract power requiring a ...
jessegerritsen's user avatar
0 votes
3 answers
77 views

Can the power of a diesel electric generator, installed in a factory, escape into the national grid?

Say that there are two factories connected to the same 20 kV medium voltage line (see Fig. 1). Each of them has 400 V motors that consume power by turning some machines acting as mechanical loads. One ...
Robert Werner's user avatar
0 votes
2 answers
74 views

Force required for a power generator in a coal power station

I am unsure about how to word this question properly and I assume that it might take two directions probably because of the unknown variables involved but here goes... On the actual physical power ...
Blurry Sterk's user avatar
1 vote
2 answers
543 views

Can an electric motor act as a load for the electric generator rotated by that motor?

I have an experimental generator and an off-the-shelf motor that I intend to arrange like in Fig. 1. The problem is that if I connect the required load to the output of the generator the power drawn ...
Robert Werner's user avatar
0 votes
1 answer
74 views

Is there any way to relate the induced EMF from an alternator to the DC current that is used in the field winding?

I'm trying to simulate the open circuit saturation of an alternator. Basically, by changing the amount of current that is going through the field windings (rotor), the voltage induced in the armature ...
Aldrin Cedre's user avatar
0 votes
2 answers
43 views

How can I express parameters of a natural gas generator in terms of a diesel generator?

I am using the REOpt tool from the U.S. National Renewable Energy Lab to help in sizing a new battery energy storage system and solar PV array for an existing building. The building already has a ...
LShaver's user avatar
  • 449

15 30 50 per page