Questions tagged [wheatstone-bridge]
A circuit to measure an unknown resistance.
215
questions
1
vote
2
answers
58
views
How to simulate for the Gain of opamp Bridge Differential Amplifier?
Hi experts,
I have this circuit, with a bridge connected to an op-amp in differential form, and I want to simulate it for the Gain of the circuit in PSPICE.
I have found it's gain by hand, which comes ...
2
votes
2
answers
51
views
Wiring of INA128 instrumentation amplifier to Wheatstone bridge
Is there any issue with the wiring or calculations of my INA128 instrumentation amplifier to my load cell Wheatstone bridge? Currently I see no change in the output when connected to the oscilloscope. ...
0
votes
2
answers
63
views
Wheatstone bridge connected to op-amp: confusion about Vout formula
I am not sure when the correct formula for Vout is Vout = G(VA - VB) or Vout = -G(VA - VB).
Can you explain the difference between these two examples? The circuits and the formulas provided are from ...
0
votes
2
answers
47
views
Choosing points for analysing equivalent resistance
I realized there is something fundamental about equivalent resistance I don't understand in terms of application. I understand the part about mechanically simplifying resistors into one resistor, just ...
1
vote
2
answers
98
views
Input/output resistance for an accelerometer/Wheatstone bridge
I am looking at the MS 3028 Piezoresistive Accelerometer.
This is the internal schematic of the component, as a Wheatstone bridge, which per my understanding means it's a quarter bridge with other ...
1
vote
1
answer
412
views
Very irregular reading of load cells with the hx711 (on an ESP32)
I'm using an ESP32-S3-WROOM-1U and a four load cells, connected in a full Wheatstone bridge to an HX711 to read the weight of an ...
0
votes
2
answers
76
views
Wheatstone bridge to voltage follower circuit not working as expected
I am designing the following circuit shown in the atached image. It is a wheatsone bridge with the differential output attached to voltage followers on each terminal and then connected to a single ...
3
votes
1
answer
155
views
How to demodulate a signal that was frequency-modulated by an offset sine?
I have a strain-gauge (SG) in a Wheatstone-bridge (WB) configuration that I would like to measure on the 0-250Hz band on 16 bit ...
0
votes
1
answer
296
views
How can I apply Kirchoff Law for a capacitor in Wheatstone Bridge?
I got this question in an exam, where I was given an unbalanced Wheatstone bridge and was asked to find the voltage across the capacitor. I can't understand how to apply Kirchhoff's laws for a ...
1
vote
1
answer
126
views
How do you compensate for a varying DC offset when using a wheatstone bridge?
Background
I have a sensitive magnetic sensor that is packaged as a wheatstone bridge with a 20k
device resistance. I am using it to measure the rotation of a magnet. It is possible to calibrate out ...
0
votes
4
answers
1k
views
Wheatstone Bridge with Instrumentation Amplifier
I have set up this circuit:
I measure an output of 0.61 V from the instrumentation amplifier. The gain of the amplifier is set to 21. The formula for the output is given by:
Uout=(1+2R1/Rg)×(R3/R2)×(...
1
vote
0
answers
46
views
Online motor inductance measurement at different rotor angle
I wanted to measure the inductance of PMSM at different rotor angles. I'm familiar with the offline methods of measuring motor inductance but would like to measure a motor's inductance while it's ...
1
vote
1
answer
113
views
Analysis of Wheatstone Bridge circuit with connected output terminals
I am given the following case of a Wheatstone Bridge circuit where the output Terminals \$U_{a}\$ and \$U_{b}\$ are connected with a wire and need to derive both output voltages as functions of the ...
3
votes
0
answers
94
views
Determining resistors in a Wheatstone Bridge from Ohmmeter readings - Unsolvable system of equations
I have been challenged in an assignment that uses a Wheatstone bridge to find values for the resistances in each arm, given that they are 1 kOhm +- 1%, and using only Ohmmeter readings and short-...
0
votes
1
answer
62
views
Help testing Pressure Sensors
I have a few ME600 Metallux sensors that I harvested from some discarded products. I want to build a project with these but would like to verify they work before getting too far. From the datasheet ...