Questions tagged [solenoid]
An electromagnet combined with an actuator to convert electrical energy into linear physical motion.
640
questions
0
votes
1
answer
32
views
Using a Relay to control an irrigation valve solenoid
I'm using a JQC-FC3VDC relay. I control it from a microscontroller using a 3.3V signal through an opto-link. And the business end of the relay controls a 24VAC output which then activates the ...
1
vote
0
answers
22
views
Sprinkler controller couples electrical noise between stations, firing wrong solenoid
I've been trying to troubleshoot a Toro DDCWP 4 battery-powered sprinkler controller which started exhibiting strange behavior this summer. This is a basic four-station controller paired with RainBrid ...
0
votes
0
answers
23
views
Should solenoid be connected to NO or NC terminal of RF remote to retract plunger end off of edge of tiny spring-loaded door so it can snap closed?
Remote-control nestbox bird trap. End of solenoid plunger will rest on edge of the tiny, spring-loaded trap door to hold it open until remote control is used to trigger solenoid to retract, releasing ...
2
votes
1
answer
40
views
does rf remote transmitter power affect solenoid strength
Remote-control nestbox (bird) trap design calls for one 9V battery (pack with switch) boosted to 12V with MT3608 module to power 12V 433Mhz RF remote receiver, which is connected to a ZEY1-0530 ...
1
vote
0
answers
38
views
Ring Video Doorbell / ghost rings with 16 VAC solenoid chimes [closed]
I have:
Ring Video Doorbell
(x4) solenoid chime operating on 16 VAC
The chime is a pre-2000's analog device. Presumably it uses an analog circuit to ring the solenoids in a pattern to make a ...
1
vote
1
answer
72
views
Did I draw my circuit diagram correctly for 2 MOSFETS and a solenoid?
My project consists of one 5 V solenoid (but uses 3.3 V), one voltage regulator (5 V to 3.3 V), one diode, two N-channel MOSFET transistors, and one 5 V LED strip, all controlled by a Raspberry Pi ...
0
votes
1
answer
36
views
Issue controlling MOSFET with PCF8575
I'm currently trying to control an array of MOSFETS so I can drive several solenoids. I'm using the Boron from particle.io as my main board, the PCF8575 as my I/O expander, the MAX3004 as a level ...
4
votes
4
answers
1k
views
Can a slanted magnetic field be created with this insulated stranded wire arrangement?
I am considering building a small-scale experimental coil gun because I have an idea of how a magnetized projectile could be rotated while it is traveling through the coil(s), similar to how a bullet ...
-1
votes
2
answers
109
views
Did I draw this circuit diagram correctly for 2 MOSFETS? [closed]
Did I draw my circuit correctly?
My project consist of one 5 V solenoid (but uses 3.3 V), one voltage regulator (5 V to 3.3 V), one diode, two N-channel MOSFET transistors, and one 5 V LED strip all ...
2
votes
2
answers
182
views
H-bridge with two logic-level GPIOs drawing high current
I am working on controlling a bi-stable latching solenoid with an H-bridge.
The microcontroller that I am using for my project doesn't have enough GPIOs for me to use four pins for the H-bridge, so I ...
0
votes
2
answers
77
views
Why is this Zener across the collector and emitter of this transistor driving a solenoid coil?
I am trying to understand a vintage (1970s) impact printer circuit. Each of the pins in the printer are driven by a small individual coil driver circuit, that was originally specified to look like ...
3
votes
2
answers
706
views
Why is this zener in series at the base of transistor, and has something failed?
I am debugging an ancient little impact printer and in my probing have found an unexpected voltage level. I'd like to understand this part of the circuit, why it's constructed as it is, and whether ...
7
votes
1
answer
213
views
Equation for the force created by a solenoid
I'm trying to make an electro-magnet and I want to figure out what core and wire I need using math instead of trial-and-error.
I want it to produce ~1.5 newtons of force at ~1.5 inches from the magnet....
0
votes
3
answers
148
views
Issue with solenoid valve sparks despite using two 1N4001 flyback diodes [closed]
As a student, I'm currently working on a science project where I intend to connect a 12V, 2A solenoid valve to a relay and subsequently to a Raspberry Pi Pico. The solenoid valve is powered by a 12V, ...
0
votes
1
answer
87
views
How do I read the specifications on this DC contactor?
This is a solenoid from an Italian made marine windlass.
Could you please help me understand the specifications written on it?
From what I know, the coil and connector is 12V because that is the ...
0
votes
1
answer
32
views
Linear Solenoid Pulsed
I have this part from RS: https://docs.rs-online.com/4238/0900766b81679254.pdf.
I understand quite well about why the solenoid can output more force (given same distance) or have higher power input (W)...
0
votes
0
answers
107
views
PCB layout/schematics of solenoid lock control - Problem - uncontrollable unlocking
I have a problem with opening solenoid locks. Sometimes, immediately upon connecting the power, and other times after about half an hour or even an hour, the locks start to open uncontrollably.
I have ...
0
votes
1
answer
108
views
Is my PCB ready for PWM solenoid control?
I am looking to upgrade my project to handle "back EMF" from solenoids when used in PWM mode in combination with MOSFET.
The original project lives on a breadboard, and I am attempting to ...
0
votes
3
answers
253
views
Inductance of solenoid with solid metal core
Consider the solenoid/inductor like in the picture.
There is an air gap between the coil and the inserted solid metal.
The solid metal is from aluminum or copper (Both have a relative magnetic ...
0
votes
2
answers
71
views
How to get a smooth operation of multiplexed solenoids
My project involves 100 small solenoids, that I either have drive individually, or hopefully I can drive in a multiplexed configuration, the same way LED displays are driven. Then I only need 20 ...
3
votes
2
answers
347
views
Problem driving solenoids with an IRF540 power MOSFET
I am using an IRF540PBF power MOSFET to drive a solenoid with 24VDC which works beautifully. When I try to drive a stronger solenoid the MOSFET gets stuck in the on position until I power the system ...
1
vote
0
answers
116
views
Testing a 24V motor - Can I simply connect posts to a 12v battery?
I need to test if a 24V motor works or not. How can I test this just to make sure it functions? Is it possible to simply connect a 12V battery to the 2 motor posts and see if it spins, then reverse ...
1
vote
2
answers
87
views
Driving 12V hand wound solenoid using PWM
I'm trying to drive a hand wound solenoid (140 turns of 0.8mm enamel copper wire, 4cm long) with a 12V/2A power supply. I need to control the intensity of the force generated by the solenoid, so I'm ...
0
votes
2
answers
112
views
Solenoid fails under PWM control
I have a 12V solenoid rated at about ~6W and 40kg pull.
I am controlling it using ESP32, IRLB8721PBF logic-level mosfet.
MOSFET gate-gnd is also connected using 0.5W 5.6V zener diode.
ESP32-gate is ...
1
vote
1
answer
112
views
Finding the ideal parameters for a homemade electromagnet
I am making an electromagnet and I was watching some videos on designing one. I just have some misunderstanding about power calculations of electromagnets and I have some questions about it.
Q1)
1.1) ...
0
votes
2
answers
88
views
Am I using these MOSFETs correctly?
I am designing and testing a circuit that charges a capacitor to around 50V using a boost converter when 'ARM' is high, then discharges it through a solenoid when 'FIRE' is high. ARM and FIRE are ...
1
vote
3
answers
104
views
Maximum safe wattage for solenoid and duty time
Please can somebody put my mind at rest?
I work on a machine that is unpowered until fully assembled and it has a push-pull solenoid (195222-237).
It has become apparent that we need to cycle this ...
1
vote
2
answers
230
views
What capacitance would I need to actuate a solenoid?
I have a project that requires I hit a 5 cm ball with a push-pull solenoid.
For the purposes of the project the solenoid needs to be actuated using a capacitor, but after reading multiple forums, I am ...
0
votes
0
answers
22
views
How to connect a solenoid to the Adafruit Feather M0 Bluefruit LE
How would I connect the to the Adafruit Feather M0 Bluefruit LE to this Mini Push-Pull Solenoid - 5V so that I can via bluetooth send over instructions to the microcontroller to control the solenoid?
2
votes
2
answers
156
views
Does winding a solenoid around a copper pipe reduce the net magnetic flux at all?
I want to wind an air core solenoid around a copper tube. One end of the solenoid is soldered to the copper tube. (See picture above). Will a magnetic field be induced in the copper tube that cancels ...
0
votes
0
answers
74
views
What kind of relay / switch is this?
What kind of relay, if I'm right, is this? It is used in a PRCD.
Pictures from 3 sides.
1
vote
1
answer
67
views
Different types of linear solenoids
I want to use a linear solenoid and there are different types, pull, push and pull/push.
So I chose a push solenoid for my application and saw the following picture.
I know that the plunger goes ...
1
vote
0
answers
102
views
Proper circuit for a solenoid being triggered by a relay with occasional misfires
12V relay question…
I built a homemade pinball controller for my PC using a standard, 5 V USB encoder for the controls. I wanted to add some haptic feedback, so I decided to add a few 12 V solenoids ...
0
votes
1
answer
71
views
Optimizing Solenoid Control Circuit with FETs: Minimizing Inrush Current and Hold Current Precision
I'm creating a circuit using two FETs. The first FET (U2A) is responsible for controlling the inrush current of the solenoid, and the second one (U2B) is used to maintain the predetermined hold ...
0
votes
0
answers
58
views
Noise spikes with optoisolated circuit driving 12VDC solenoid valve at 6.6 Hz
I have an existing circuit that drives a 12VDC solenoid valve on and off at ~6.7 Hz, 75ms on, 75ms off. This entire system is DC.
The Beagle GPIO logic '1' level is 3.3VDC, and the BeagleBone is ...
10
votes
3
answers
1k
views
Why did the Lucas voltage regulator use rectangular section enameled wire for one of the windings?
In the 1930s and subsequently, Lucas supplied a car voltage regulator of the twin bobbin type.
A detailed description of how it operated can be found here, but in summary, one solenoid operated a cut-...
0
votes
4
answers
126
views
I have a solenoid rated at 24 volts AC, but at a trickle voltage of 1-9 volts the solenoid stays pulled in when it shouldn't be
I have a solenoid that pulls in at 24-30 volts ac to control water flow. It opens at 24 volts ac, but stays pulled in at a trickle voltage of .75 -1.0 volts. How can I stop this from happening?
0
votes
1
answer
48
views
Relationship between RMS-current and energy stored in a solenoid
Regarding the formula for energy stored in the magnetic field of a solenoid (U=1/2LI^2), I presume that the RMS value for an alternating current could be used for the I-value. Is this correct?
0
votes
1
answer
199
views
Diode in parallel with AC solenoid valve
I have a circuit I'm trying to design to fire both 120VAC and 24VDC solenoid valves. We have relays that work on 12vdc for the coil, and can switch AC or DC. the valves are normally around 30W. I ...
1
vote
1
answer
550
views
Modelling solenoid with LTSpice
Does anyone can give me a hint on how to modelling a solenoid (solenoid locker) with LTspice ?
Here is the characteristics from the supplier (https://www.lextronic.fr/mini-serrure-solenoide-12-v-58746....
3
votes
1
answer
367
views
How can I build the attached circuit diagram in a bread board?
How can I build the attached circuit diagram in a bread board? I've procured all the mentioned components.
The components I have are:
BLM5 Solenoid,
Vishay 100V 3A rectifier diode,
Welwyn 39Ω wire-...
0
votes
1
answer
163
views
Is this (working) 2-doorbell system dangerous?
In a previous setup, I had two doorbells, each one with its own 10V AC transformer, as detailed in Why is it impossible to connect these two doorbells in series or parallel?.
I now know it was ...
7
votes
3
answers
2k
views
Why is it impossible to connect these two doorbells in series or parallel?
I have:
one 220 V AC -> 10 V AC transformer
one push-button switch (at the door)
two bells for two different places of the house; they should ring together when the (single) door push-button ...
0
votes
0
answers
55
views
How does this motor work?
I have been on a bit of a quest to find some sort of linear motion device to compress a spring with 15kg of force 80mm at 1600mm/s, with continuous duty cycle, ideally under $40. So I was digging for ...
0
votes
3
answers
127
views
Linear Motor Design
I previously uploaded a question on trying to make a solenoid attract a magnet 80mm away, however this ended up being an impossible ask due to solenoid's having a max effective attraction distance of ...
0
votes
0
answers
22
views
How to operate and choose the right components to control an industrial pull and push solenoid using an Arduinuo?
Push/Pull which has a 24 V DC power supply and power consumption of 23/85/400 W.
What transistor and diode configs I should be going for?
0
votes
1
answer
164
views
Strong Compact Solenoid Design
I have a spring that I need to compress 80mm. To do so requires approximately 15kg of force. To compress the spring, I will have the spring in front of a piston head. The piston head will have a ...
0
votes
2
answers
446
views
Solid state relay driving an inductive load
I want to drive several irrigation solenoid valves with solid state relays. The solenoid in question is a Hunter model 606800 24V AC device. Its specifications state 370mA inrush current and 210mA ...
0
votes
1
answer
80
views
Understanding Solenoid Datasheet
I have a 3/4" tubular pull-type solenoid from Magnetic Sensor Systems, model number S-15-75-24. The datasheet can be found here: http://www.magneticsensorsystems.com/solenoid/tubular/s-15-75.asp
...
0
votes
1
answer
72
views
What kind of solenoid is this?
My electrical water timer broke, and interested to see its inside I opened up and found this (image) solenoid. I'm not sure what type it is.
The whole thing runs on 2xAA (2x1.5V) batteries, but it ...