Questions tagged [schottky]
A Schottky diode is a diode formed by the junction of a semiconductor with a metal. A Schottky diode has a lower forward voltage drop and faster switching speed than a standard silicon diode.
245
questions
0
votes
2
answers
61
views
Identify single diode top marking A2, SOT23 (SOT23-3) package
I need to identify a diode (it may be a Schottky) single channel with top marking A2 in SOT23 (SOT23-3) package.
0
votes
0
answers
50
views
Easy Overvoltage and Reverse polarity protection circuit
I'm looking for the simplest and most effective way to add an overvoltage and reverse polarity protection network to a signal line connected to an MCU, the maximum allowable voltage at the MCU pin is ...
-1
votes
2
answers
47
views
Does the three-pin diode have a half current? [closed]
I need a 30 amp diode for the battery backup. I have used an MBRF30100CT diode. But I don't know the diode current is 30 amps or half of it is 15 amps.
0
votes
2
answers
112
views
The effect of silicon diode vs Schottky diode as reverse voltage protection of a LED
I have a 24Vac, 50Hz source and RGB LED to be driven from it. As the LED reverse max is like 5V, I have to prevent the reverse half cycle of voltage from being applied across the LED. There are two ...
4
votes
4
answers
865
views
Op-amp with Schottky diode
I'm struggling to understand what the sense is of using the two Schottky diodes in this excerpt of a circuit:
I understand how a Schmitt trigger works. The diodes ensure that the voltage difference ...
0
votes
2
answers
111
views
Why does a boost converter need 11 mA without a load?
I use a FP6296XR-G1 (U10 / 10A boost converter) together with a MBR20100CS (D5 / dual Schottky diode in a TO252-2 package) in order to make 13 V out of 2.5-5 V.
When I connect BOOin to 5 V from an ...
0
votes
1
answer
159
views
Switch between two DC sources using Schottky diodes
I'm building a small power bank as a backup for my router due to frequent power outages. The router takes 12 V 1 A, even though, it can take between 10-15 V without an issue.
I'll be using CC/CV ...
0
votes
3
answers
199
views
Eliminating Negative Voltage Pulses (≤ 840 mV)
I have obtained a voltage signal from a Weigand sensor (a sensor that creates a low voltage signal when placed in a rotating alternate magnetic field), which generates a positive pulse of 1.2 V and ...
2
votes
0
answers
201
views
ESP32 with two power supplies (AC/DC + USB) using Schottky diodes
I'm building a small circuit to power an ESP32 with two different power supplies.
Normally the circuit will be powered from AC, using a Mean Well IRM-02-5 AC-DC power supply to get 5VDC out of 220VAC.
...
1
vote
1
answer
115
views
Non-Schottky SiC diodes
Hopefully this isn't too much of a shopping question. I am looking for off-the-shelf silicon carbide P-N junction diodes, but all I can find are Schottky ones. Do P-N version ones even exist ...
2
votes
1
answer
66
views
High voltage at the Schottky's anode terminal (Hobby Li-Po charger circuit)
I'm pretty new at hardware side of things and trying to teach myself circuit and PCB design just as a hobby, so. bear with me if I'm annoyingly noob for you.
As a relatively simple first task, I ...
1
vote
1
answer
103
views
What is this 2-pin motherboard component and is it broken?
I own a ASUS FX505DT Notebook and the fans stopped spinning so I wanted to check the voltage with a multimeter. I accidentally slipped of one of the terminals and released some "magic smoke" ...
2
votes
1
answer
256
views
Are there any Schottky-diodes that can replace the ones on this PCB?
I want help with finding Schottky-diodes to replace the ones on the PCB bordered in the red rectangle. They are probably non-working as they failed the continuity test with a multimeter. I have two ...
0
votes
1
answer
44
views
FDMS7658AS SyncFET replacement for a regular one, burned it
I have a 3rd-party circuit (dimming 5V bulbs), which suddenly stopped working.
The FSMS7658AS mosfet was dead.
Here is the datasheet »
The key parameters are: N-Channel PowerTrench® SyncFET™; 30 V, ...
0
votes
2
answers
114
views
CRS01(TE85L,Q,M) Schottky diode is open both ways
I was testing my PCB when I noticed that I get +12 V on USB Vbus line, even though I placed a Schottky diode to block it.
The idea is to use +12 V voltage source to provide power and to connect USB ...