Skip to main content

All Questions

0 votes
0 answers
42 views

How can a power converter small signal model predict transient behaviour during a load step which is a large signal disturbance?

I see small signal model being used to predict the Overshoot/Undershoot of output voltage due to a load step. How do we justify this approach, since the basic assumption of small signal modelling is ...
Dynamic_equilibrium's user avatar
3 votes
2 answers
139 views

Is there a way to take this buck diagram and reduce it to an AC transfer function?

I am semi-dangerous with switchers but I've never really delved into the innards of them so I'd like to ask about this TPS23750 diagram. I would like to develop a model of this feedback loop of a buck ...
Voltage Spike's user avatar
  • 84.8k
1 vote
1 answer
54 views

Modeling first-order dynamics of a switching converter

I have created a simple, first-order model of a switching regulator in steady state (it's basically a transformer with a loss element). Its only parameters are desired output voltage \$V_o\$ and ...
divB's user avatar
  • 1,326
0 votes
2 answers
142 views

How does current flow in this circuit with multiple power regulators?

I have the following circuit: simulate this circuit – Schematic created using CircuitLab U1 contains two voltage regulators (Vo1=+10V, Vo2=-10V, input Vin=5V). (These could be buck, boost etc. ...
divB's user avatar
  • 1,326
2 votes
2 answers
964 views

Different levels of SPICE models

I wanted to model some components operated in a switching boost power converter at LTspice and i realized that different levels are available for power mosfets. Do all components have different levels ...
WeTech's user avatar
  • 735
1 vote
4 answers
267 views

Loss-free resistor model

Can someone use a simple explanation to tell me what a loss-free resistor model is? I googled it but it is hard to understand. When I study power factor correction circuits, I see some papers use this ...
EEC's user avatar
  • 413
0 votes
2 answers
4k views

Average PWM Switch Model

I'm trying and want to learn how to use the PWM Switch Model by DR.Vorpérian , both for the voltage mode(VM) and current mode (CM) model. I've read some about the models in "Switched-mode power ...
user103776's user avatar
0 votes
1 answer
611 views

Derivation for average value input current in buck-boost converter

I am struggling with the derivation of average value of input current as below. The image is from the lecture here (page 26). Here is what I got so far. How did the lecture derive the final step here?...
emnha's user avatar
  • 1,649
0 votes
2 answers
1k views

hamonics and sidebands in dc-dc converter

The lecture (page 8) shows output voltage spectrum with sinusoidal modulation of duty cycle of a dc-dc converter. I am wondering where the hamonics and sidebands come from. For hamonics, I read ...
emnha's user avatar
  • 1,649
4 votes
3 answers
2k views

Push current source through transfromer

This lecture (from page 130) shows manipulation of the buck-boost converter model into canonical form. I am stucked at moving current source through transformer as in the picture below or from the ...
emnha's user avatar
  • 1,649
1 vote
1 answer
559 views

ac model for buck-boost converter

This lecture shows how to create ac model for buck-boost converter. What I am confused is the equivalent circuit model for inductor loop equation on page 38. As you can see from the model, there ...
emnha's user avatar
  • 1,649
10 votes
3 answers
1k views

What causes this knee in my MOSFET drain voltage drop?

FINAL UPDATE: Understand a previously mysterious power MOSFET switching waveform wiggle! @Mario uncovered the root cause here below, distinctive to so-called VDMOS devices, typical of many power ...
scanny's user avatar
  • 7,172
0 votes
1 answer
282 views

Transient analysis of a step down converter with control loop

I am trying to run a transient simulation of a step down dc-dc converter using ideal components. This includes a feedback loop consisting of an error amplifier. I am interested in transient response ...
JGalt's user avatar
  • 887
1 vote
1 answer
498 views

AC-model of Integrated Boost-Flyback converter

I am designing a small SMPS to light a few Nixie tubes from an ordinary USB charger. This requires a high voltage gain around 40 which disqualifies many of the typically used topologies. I have grown ...
A. Drott's user avatar