Questions tagged [electrolytic-capacitor]
An energy-dense polarized capacitor type, used in low-frequency filtering applications.
372
questions
0
votes
1
answer
28
views
Multiple smaller capacitors on power rail for NeoPixel / WS2812B strip
I read in the AdaFruit guide that a 500-1000uF capacitor is recommended on the power rail.
However, electrolytic capacitors in this capacitance are quite large. Depending on the length of the strip, ...
0
votes
1
answer
68
views
Cyclic Voltammetry for a Capacitor - Positive Current, Potential is decreasing?
In the boxed red region, why is the potential decreasing when the current is still positive? To my understanding, when the current is still positive (i.e. not changing direction), the capacitor will ...
1
vote
2
answers
92
views
Decoupling capacitors for operational amplifiers
when in the refence design of an amplifier (for example OPA856) we see the + sign in a capacitor schematic, does this necessarily means we should use electrolytic capacitors?
If there is no positive ...
-3
votes
3
answers
120
views
Blowing up capacitors with a 9v battery [closed]
Hello, I have a 9V battery I would like to blow up some capacitors with; currently I have 6.3v 180uF capacitors that don't seem to blow up at least in a good time(I'm aiming for <5 seconds), they ...
0
votes
0
answers
21
views
Lithium Ion Battery : Electrolytic Capacitor At Buck Converter Output
It is recommended not to parallel electrolytic capacitors with a battery due to the leakage current of the electrolytic capacitor (which is small but worthy of consideration over large time periods) ...
1
vote
1
answer
87
views
Electrolytic 3-lead capacitor
I have a 3-lead capacitor that I'm having a hard time identifying. It is from an old Lafayette PF-30 receiver. I don't have schematics or a manual.
It has a high squeal when turned on, and my first ...
1
vote
1
answer
56
views
Possibillity of reverse polarity of Aluminum Electrolytic Capacitor
Introduction
First of all, this question more like theorical rather than practical as I want to test my understanding about Aluminum Electrolytic Capacitor, which I will later called Al-Cap for short.
...
0
votes
1
answer
57
views
Power schematic questions
I received a guitar pedal in poor condition and looking to repair. Checking through the schematic, it appeared the electrolytic caps were installed backwards. All other picture I could find online ...
2
votes
1
answer
296
views
How to identify surface mount electrolytic capacitors?
Various surface mount electrolytic capacitors seem to have no consistent marking method. Here are some examples:
(Image sources: 1, 2, 3)
How can I identify what value and voltage rating these are?
0
votes
1
answer
233
views
Probability of explosion of a 100 µF, 25V capacitor when powered at 5V [closed]
I have a system which uses this board: Arceli Motor Control Speed. It's supposed to run for a maximum of 5 hours continuously.
It has an electrolytic capacitor (black vertical tube) on which is ...
1
vote
1
answer
182
views
How does temperature affect ripple current parameter in electrolytic capacitors?
A maximum ripple current declared, for example, at 100 kHz and at a temperature of +105 ℃ for an electrolytic capacitor, if estimated at a temperature of +85 °C, how much does it increase? What order ...
0
votes
1
answer
141
views
Can you replace ceramic or tantalum capacitors with aluminum electrolytic capacitors?
I have a question about the hookup for my 12VDC to 5VDC step down module - the K7805JT-500R3.
It states in the datasheet that ceramic capacitors are what can be used but it also states that tantalum ...
1
vote
1
answer
205
views
EMI filter attenuation requirement for a buck converter given EMI compliant AC-DC converter
In my application I have an off the shelf 600W 72V AC-DC converter that generates the main DC bus that powers a custom board that houses a 72V input, 9A output buck converter switching at 330kHz. A ...
0
votes
1
answer
83
views
Calculate capacitor charging constant time connected to battery and boost converter
I know the formula to calculate the constant time for capacitor is t=RC and for full charge t=5RC.
In the following example there is not resistor in the circuit but of course we are not in the ideal ...
0
votes
2
answers
125
views
What is the capacitor needed for 30 kHz power rectifier?
I need to rectify 200 V at 30 kHz for a resistive load of 3-4 kW. I use a 1200 V/60 A Schottky diode bridge. I have some 6800 uF/450 V capacitors. Can I use them, or should I use other values? Is ...