Questions tagged [edge-connector]
The edge-connector tag has no usage guidance.
14
questions
0
votes
1
answer
32
views
Need help identifying tiny 2 pin connector [closed]
I managed to break on side’s retaining tabs on this tiny male 2 pin connector while rebuilding my Dyson V-10. Searched all over trying to find its likeness. Any help would be appreciated.
enter image ...
- 1
2
votes
0
answers
71
views
What connector is this? (1.2 mm pitch pad array)
I have a mystery board which has 196 pads that are meant to connect to something.
The pads are arranged in four staggered rows of 49 (4 × 49 = 196). The pitch is 1.20 mm exactly. I double-checked, it’...
- 3,491
15
votes
2
answers
2k
views
PCB Edge connector: nipples on each finger?
I am designing a footprint for a PCB edge connector. The datasheet shows in DETAIL 'A', some "nipples" at the end of each finger. I don't understand note 5 and I don't understand what these &...
- 847
0
votes
1
answer
92
views
Proper terminology for connectors that goto the edge of the PCB
A PCB can contain many different connectors. Some of these shall exist on the edge e.g USB connector, power barrel connector, Ethernet connector, Serial port, HDMI, DVI, Parallel port e.t.c. All these ...
- 2,103
1
vote
0
answers
97
views
1
vote
1
answer
517
views
Custom card edge connector components
Let me start by saying I made a poor design choice up front, but I'm stuck with it for a while so I'm trying to work around it.
I'm making some custom test chips that feature ~200 nm of gold patterned ...
- 185
0
votes
1
answer
125
views
Card edge connector "read out" meaning
I'm looking for a card edge connector to short the pads on one side of a PCB card to the pads immediately opposite them on the other side of the card. Digikey specifies an attribute called "read ...
- 1,053
0
votes
2
answers
235
views
Socket for old edge connector
I have an old PCB with an edge connector and I am looking for a way to create a socket for it. I have a 3D printer, so the housing is not an issue, but where I am stuck is the contacts.
The edge ...
- 321
0
votes
0
answers
813
views
Has anyone tried using a via as a receptacle for pogo pins?
I am in need of building a lowcost magnetic board to board connector.
There will be a lot of modules and a connector that connects both sides is needed 6x on each pcb.
I need a connection similar to ...
1
vote
3
answers
466
views
Is there a component that will provide an elevated SMD pad?
Is there a surface-mount component I can put on a pad, that simply has another pad on top that I can solder something on to?
Here is a side view showing pins above the pads that would need bent down ...
- 355
2
votes
1
answer
111
views
What is the name of these connectors? (XBee Radio Module)
I'm migrating a design from an older through hole module, to a new module that has edge connectors. The dev kit has these nice spring loaded connectors on the carrier board where the module just pops ...
0
votes
0
answers
89
views
Is there a way to make a edge to edge connection only using external magnets and gold fingers?
This question might sound pretty stupid, but I have been searching for solutions for a few days, so all of your new ideas are highly approsciated.
I am on a hunt for a solution for modularly ...
5
votes
1
answer
450
views
Any downsides to greasing electrical connections?
I learned long ago, living in Buffalo NY, that any and every electrical connector I service in my cars needs grease stuffed in it or it rusts out FAST
So why don't we put any grease or other coating ...
- 4,618
1
vote
2
answers
320
views
PCB edge connectors for either board to board and screw terminal
I am at the final stage of design a pcb and I am looking for a connector to power it (2 pins, more would be also ok).
It has 2 use cases:
I could be either used as a standalone product, in this case a ...
- 447