Questions tagged [bias]
A DC voltage or current in a circuit to set the operation point of an active or non-linear component.
417
questions
1
vote
0
answers
71
views
Best place to add DC biasing
I'm working on a circuit where I have a CS4344 audio DAC feeding into a LM324 inverting amplifier that uses 1.2v as a reference voltage.
I'm staring with the example circuit shown in the CS4344 ...
0
votes
0
answers
49
views
Please provide your comments on this circuit idea of mine for bias generation?
There is a requirement for a P-side current generation. Currently we have P-side Vt/R solution which is the left branch in the figure, except it is diode connected. When the PMOS is diode connected, ...
1
vote
1
answer
73
views
Do FETs need to be biased?
From my knowledge, BJTs need to be biased to control its linearity and gain, usually with resistors on the base and collector.
Suppose I want a FET in saturation acting as a high-side switch.
Do FETs ...
2
votes
1
answer
48
views
AC analysis of a Bias Tee
I am designing a bias tee here and wondered whether it actually works or not? Hence I conducted an AC analysis instead of S-parameters (after verifying that s parameters are okay). The bias tee has ...
1
vote
1
answer
51
views
Solid-state relay input characteristics
I am a bit confused by some of the specification on this solid state relay LD00KM. I am looking at the case in which this relay is used in the 2 Terminal Input (Direct Drive) Configuration as shown in ...
0
votes
0
answers
53
views
Biased Clamper Circuits
I have been tasked to design a clamp circuit to clamp the negative extreme of a periodic input waveform to −5 V. I can use diodes, zener diodes, and resistors of any values required. I will assume a 0....
0
votes
0
answers
50
views
DC Bias network for a LCR meter
I am trying to make a DC bias network for my LCR meter (Scientific SM6023) based on this circuit I found online
RD10E has a Zener voltage of about 10V and 1N4004 has a forward voltage of 1V. I have ...
0
votes
1
answer
72
views
Direction of Op Amps Input Bias Current relative to declared sign on datasheet
Input Bias Current is a parameter of Op Amps related to the Base/Gate currents flowing in or out of the differential amplifiers at the input of the amplifier. It is calculated as the average value of ...
1
vote
1
answer
104
views
Non inverting opamp with bias DC
I'm doing a lab work on a circuit that takes a square signal in the input and first amplify it, then shape it and the amplify it again. So the circuit is actually composed by: an amplifier (inverting),...
0
votes
1
answer
57
views
Can a capacitor be used for biasing?
I have a load switch IC SiP32431DN which internally has a comparator at its input stage (connected to its on/off pin). If I connected a, let's say, 100nF capacitor to this on/off pin, would that be ...
0
votes
1
answer
116
views
Instructables DIY current limiter circuit [duplicate]
I found this inline and was hoping if that circuit is okay. Instead of a battery though, I want to use a dynamo (plenty of juice-wise).
Output of dynamo is 18 V 200 mA. I wish I could adjust the ...
0
votes
1
answer
138
views
MOSFET transconductance
I am curious what the relationship is between the drain bias current and the transconductance of a MOSFET? For instance, say you set V_DS but you double the drain bias current, how would this affect ...
1
vote
0
answers
84
views
MAX9924 input signal and bias?
I'm trying figure out how to connect a MAX9924 ("Variable-Reluctance Sensor Interface with Differential Input and Adaptive Peak Threshold") to a sensor on a rowing machine. My knowledge of ...
0
votes
0
answers
94
views
Vintage Intercom BJT Preamplifier: Purpose of Capacitors and DC Bias Troubleshooting
EDIT - Further Research - Comments on Common Emitter Preamplifier
https://sites.google.com/a/davidmorrin.com/www/home/trouble/transistors/amplifiers
The preamplifier stage in the circuit below has ...
0
votes
0
answers
31
views
Stability factor and stiffness of voltage divider on a transitor
Does stability factor and stiffness of the bias network have a connection? this site mentioned something about stability factor so i was wondering if its thesame thumb rule about the current in ...