Skip to main content

Questions tagged [7805]

7805 Voltage Regulator IC is a member of 78xx series of fixed linear voltage regulator ICs.

28 votes
7 answers
41k views

Can I use two 7805 ICs in parallel to get double current capacity?

I use a 7805 for a project where the circuit needs a higher current (~2.8 A) at 5 V. So I assume that if I use both ICs in parallel I can increase the maximum current capacity. Would it work?...
Ridham's user avatar
  • 646
34 votes
7 answers
25k views

Optimize heat sink design - connect cooling pad on PCB backside by vias

In one of my current projects I'm using an MC7805 in a D2PAK package to generate my logic supply of 5 V from an available 24 VDC supply. The current required by the circuit is 250 mA. ...
KarlKarlsom's user avatar
  • 1,822
30 votes
3 answers
34k views

Why is there always a capacitor on input and output of a voltage regulator?

Looking at the datasheet I can see that the voltage regulators are not just a zenner diode inside, they are complex devices. I have noticed that there is always a capacitor at the input and another ...
quantum231's user avatar
6 votes
5 answers
6k views

What is the purpose of the 7805 input capacitor?

Most 7805 datasheets specify an input capacitor of 0.33uF or so. This one (the LM340 http://www.ti.com/lit/ds/symlink/lm340-n.pdf) at least specifies that the cap is only required if the regulator is "...
mhz's user avatar
  • 1,010
5 votes
3 answers
3k views

Can a 7805 ever oscillate?

I see many references to input and output caps helping with "stability" and some outright references to preventing oscillation in both answers on this site, and even in some data sheets. I also have ...
mhz's user avatar
  • 1,010
1 vote
2 answers
51k views

How to unhide hidden pins in proteus?

Recently I was designing a PCB for my project using 89c51. I am using a 12V battery to run motor and 7805 to give 5V to 89c51. When going to ARES for PCB designing I realised the VCC pin of 89c51 is ...
devansh's user avatar
  • 45
8 votes
3 answers
2k views

7805 voltage regulator reverse polarity

I'm working on a project for which I need to use a 7805 voltage regulator. I feed 9V to its input pin and power a 5V board with the output. However, when the board is connected to a computer, the ...
EightBlueLemons's user avatar
6 votes
2 answers
376 views

What is the purpose of the 7805 output capacitor?

How does a cap on a regulator output improve transient response? Is this cap not more appropriately drawn next to the load where it is not being defeated by intervening trace inductance? Or does this ...
mhz's user avatar
  • 1,010
6 votes
3 answers
5k views

L7805 destroyed - why?

I used a L7805 to power a Raspberry PI and it worked for about 10 seconds then started to smoke and die. L7805 is rated for 1.5A and 35V DC input. Power supply was 24V DC (was actually two plugin 12V ...
Peter Quiring's user avatar
5 votes
6 answers
4k views

How to place a 7805 voltage regulator on a breadboard?

I have this breadboard and I have started experimenting with pic micros. In doing so I have needed a 5 volt power supply. I have seen several tutorials for wiring up 5 volt regulator circuits on a ...
Markovian8261's user avatar
5 votes
5 answers
12k views

Selecting input voltage for 7805

I generally use switching 12V power supplies for my circuits since they are so common, but I understand the 7805 can take a lower input voltage. If I gave the 7805 a lower input voltage (i.e. 9V), I ...
Tristan's user avatar
  • 233
5 votes
4 answers
3k views

Reducing voltage drop over 7805 regulator?

I have several projects (clocks) that require 12V and 5V supply. The 5V is for TTL ICs and the 12V powers a SMPS(Switching Mode Power Supply) to give HV(High Voltage) for a tube. The 12V pulls less ...
Efram Goldberg's user avatar
2 votes
1 answer
5k views

7805 for 4-20mA current injector

I'm trying to setup a low cost current injector for testing certain I/O modules. I found a rather simple design for a current source using 7805. simulate this circuit – Schematic created using ...
Noviceeguy's user avatar
1 vote
2 answers
868 views

Positive and Negative Voltage Regualtors

I was wondering whether I could use a negative voltage regulator, specifically a 7905, as a drop-in replacement for a positive one, 7805. On closer inspection of the datasheet, I realized that pin 1 ...
fuzzyhair2's user avatar
  • 1,947
1 vote
2 answers
1k views

Why peak output current is greater than short circuit output current in 7805 voltage regulator?

This is the datasheet of 7805 voltage regulator produced by "Continental Device India Limited". Question: Why is the peak output current greater than short circuit output current? Shouldn't the ...
Srikrishna Jana's user avatar

15 30 50 per page