0
\$\begingroup\$

I have this simulation set up in Every Circuit. It can be viewed here: http://everycircuit.com/circuit/5875415639916544

For right now I have turned off M3 by jumpering M3's gate to the ground nearby. Simulating with an 18V solar panel and a 12V battery I can see in Every Circuit that when M1 and M2 are on there are some milliamps flowing to the positive terminal of the 12V battery through inductor L1. Those ma's are on M1&2's conduit.

So the software switches between HO and LO. Is VS just a ground or does some current come out of VS when HO or LO is on? The data sheet must say but I don't know where to look.

I think I understand already that D3 and C5 and R2 are for the excess charge built up in inductor L1 and a path is provided for that power to flow and dissipate when polarity is reversed on L1.I've gone through a simple buck converter in Every Circuit so I think I understand L1's diode assembly. Perhaps the concept for the diode assembly D3,C5,R2 are similar to the concept (A Buck Converter): http://everycircuit.com/circuit/6539292895608832

I've been told that C2 is a bootstrap cap for M2 however from the schematic I see that C2 is connected to M2's source not its gate as I thought it should be (or am I wrong on this?). So how does C2 bootstrap M2's gate if it is connected to M2's source pin?

I'm not sure I understand yet why in my simulation that there is no power flowing through the bootstrap cap or the bootstrap caps diode? I made a small edit where I connected that cap to the VS line.

Thank you schematic is here: http://freechargecontroller.org/images/a/ab/Charge_controller_4_04b.pdf

P.S. I've made an attempt at integrating what might happen when IR2104 is working: http://everycircuit.com/circuit/4572109894320128 In my sim software I have the option to apply a frequency so I'm thinking I can use a logic gate and two frequency voltage sources to sim the IC2. This is a lot of new stuff to me.

Screenshot (http://i.imgur.com/Pk2EsXa.png) :
enter image description here

\$\endgroup\$
4
  • \$\begingroup\$ Would it be too much to ask to post a (static) version of the schematic here? While that EveryCircuit webapp is cool, it can take a sweet minute to load... and keeps one of my CPU cores at 100%. \$\endgroup\$
    – got trolled too much this week
    Commented Jan 7, 2015 at 20:15
  • \$\begingroup\$ Sir, I think perhaps pasting a screenshot will help. I believe at this point that current is intended to flow through D2 and C2 however I'm not sure how to get that to happen in my simulator yet. \$\endgroup\$
    – Eae
    Commented Jan 7, 2015 at 22:51
  • \$\begingroup\$ N.B. the circuit in question has already been discussed at electronics.stackexchange.com/questions/127978/… The above appear to be follow-up questions. \$\endgroup\$
    – got trolled too much this week
    Commented Jan 7, 2015 at 23:30
  • \$\begingroup\$ As a general comment, I would suggest you switch to LTSpice or PSpice for simulating buck converters. The former has a built-in model for LTC6101 (and so might the latter, but I'm not sure); you'll also need a SPICE model for IR2104 which you get from its manufacturer, although IR has a rather poor reputation for its SPICE models... I hear. IR only gives models tailored for PSpice, but they usually work in LTSpice. In any of those SPICEs, you should run transient simulation; I don't know what PWM drive that board is supposed to take as input. \$\endgroup\$
    – got trolled too much this week
    Commented Jan 7, 2015 at 23:50

1 Answer 1

Reset to default
1
\$\begingroup\$

I cannot answer questions about that websim because I'm unfamiliar with it, so I'll address just "how does C2 bootstrap M2's gate if it is connected to M2's source pin?" There are several (free) appnotes that explain how that works. I see no point in parroting one, so here's a relevant excerpt from Fairchild's "AN-6076 Design and Application Guide of Bootstrap Circuit for High-Voltage Gate-Drive IC".

enter image description here

\$\endgroup\$
1
  • \$\begingroup\$ I really found this to be very helpful. I have to get my IC2 into some prototyping board. I think perhaps my IC2 functions like this. \$\endgroup\$
    – Eae
    Commented Jan 8, 2015 at 0:30

Not the answer you're looking for? Browse other questions tagged or ask your own question.