Questions tagged [lipo-batteries]
Use in reference to Lithium Polymer batteries, commonly used for their excellent energy density and their ability to provide large currents.
64
questions
1
vote
1
answer
64
views
LiPo battery cell yellow discoloration at seam
I am using a LiPo battery to power a model helicopter.
After my first flight with it i noticed a yellow discoloration around the seam of one of the cells. The battery isn't puffed up.
The voltages for ...
2
votes
1
answer
53
views
What should a LiPo's voltage be at full charge?
How can I determine what the voltage of a LiPo should be when at full charge? Specifically, what should the voltage at full charge for a 2200mAh 20c 3-cell LiPo be?
2
votes
1
answer
31
views
How 70C 2Ah batteries can have XT60 connector if it rated only for 60A current and not 140A?
Can it fit higher currents than nominal? Is it safe?
1
vote
1
answer
83
views
LiPo battery voltage keeps dropping when connected to PDB
I have an F450 quadcopter frame with the integrated Power Distribution Board. In order to use this feature, I soldered the battery (XT60) and the four ESC (Dean-T) connectors. I tested the continuity ...
1
vote
1
answer
49
views
How do I store a Li-ion pouch battery without any discharger or balancer?
I have a single-cell 3.7V 900 mAh Li-ion pouch battery and a 7.4V 30c 2s 850Mah Li-ion pouch battery. I want to store these two batteries (the manufacturer suggests I should store the 2s pack at 3.8V)....
0
votes
2
answers
383
views
A2212 1000kv Brushless motor keep beeping and twitching
I have bought an A2212 1000Kv brushless motor and a 30A ESC. I power this setup with a 7.4v 2s 30c 800mah LiPo battery. For the signal, I am using a DIY Arduino receiver and transmitter. When I test ...
2
votes
1
answer
80
views
How do I find the current my motor and speed controller will draw?
I am currently building an rc aircraft. I need to achieve approximately 20 minutes of flight time. I'm using a 1600w 320kv motor and a 80A speed controller. For 20 minutes of flight time at 80 draw I ...
2
votes
1
answer
878
views
What battery can I use for 1000kv brushless motor, that will be the cheapest?
I am using a 10 x 4.5 propeller for my A2212/13T 1000KV brushless motor with a 30A ESC. What battery will I need that will be cheap to power my motor alongside three 9-gram servos?
Flight time is not ...
0
votes
1
answer
81
views
Why wont my 1000kv brushless motor work with a 10x4.5 propeller?
When I run my A2212/13T 1000Kv brushless motor by itself with 11.1 or 7.4 volts(i am using 2 lipo 3.7volts 900mah and a li-ion 3.7v 900mah in series that I connected with alligator clips) it runs fine....
0
votes
1
answer
107
views
Can I put lipo and li-ion batteries in series
I have two 3.7 volt 900 mAh LiPo battery, which I connected in series to provide 7.4 volts. But now I want 11.1 volts.
Instead of buying another LiPo battery, am I able to put these two LiPo batteries ...
1
vote
1
answer
417
views
Can poor soldering of ESC wires lead to low voltage draw from a Lipo battery?
Question:
Would improper soldering of the power wires of my electronic speed controller limit the amount of voltage that my ESC draws from the Lipo battery?
My situation:
I have to solder an XT60 male ...
1
vote
2
answers
228
views
Amperage of FC, ESC
There is something I totally don't understand about an amperage.
According to spec. AIO FC has 5 A and 6 A ( 5 seconds). However, sometimes I see in OCD far beyond 5A and 6A. And FC, ESC are OK.
...
2
votes
1
answer
137
views
Rewiring 2S2P as 4S
I have LiPo battery that is in 2S2P configuration, however I need higher voltage (4S) battery for my project. From my understanding 2S2P battery has 4 cells same as 4S (2 in series and 2 in parallel). ...
1
vote
2
answers
665
views
How to maximize range with 2212 1400Kv motor and 30A ESC?
Premise, I'm not interested in speed or any type of sporty flight attitude, but only on range maximization I have
30A ESC,
2212 1400Kv motors 180W max with maximum efficiency current in the range ...
3
votes
1
answer
161
views
Can I use a MJX bugs 5w battery and/or charger for the MJX Bugs 5w 4k (upgraded version)?
I am wondering if I can use the MJX bugs 5w battery for its upgraded version (MJX bugs 5w 4k) as it seems they both are the same dimensions, so it can slide into the drone. Also, I am wondering if I ...
5
votes
1
answer
81
views
What battery/motor setup will replace this 1980s vintage glow engine?
I have a sport model (RCM Terrier, balsa/plywood construction covered with Monokote or Econokote stick/shrink film) that I built in 1984, and it has somehow come through multiple moves apparently ...
4
votes
1
answer
252
views
Lipo battery with an ESC and a BLDC motor
I'm not sure if I can connect four brushless dc motors to my Lipo battery. I don't know how to calculate it. The brushless motor I have is the Turnigy L2210C-1200 brushless motor (150w) and the Lipo ...
2
votes
1
answer
37
views
Is it safe/good to store a Mavic Mini 2 LiPo battery at ~18% for an unplanned next flight?
They say it is best to store at ~60% but I personally don't want to spend CC for charging it first and then discharging my battery.
Note: someone said, I can just charge the battery and unplug the ...
3
votes
2
answers
1k
views
Will wiring two batteries in parallel fry my drone?
Will connecting 2 lipo batteries of 3.7 V of 1500 mAh in parallel for a power source to a drone fry it? I understand the voltage will continue to be 3.7 V because it's in parallel. The current or Amps ...
3
votes
2
answers
43
views
Need tips on getting this to fly properly
Learning the basic concepts. Yet to use a receiver and remote. Using a 3.7 v coreless motor, lipo battery and thermocol for the frame.
I figured out how to connect the motors so that diagonally ...
4
votes
1
answer
144
views
Pros/cons of using a BEC in traditional nitro plane?
I have recently joined a local RC club, and one of the members gifted me one of his older planes. How old? 72MHz, nitro-powered, and with Ni-Cd batteries! Old school but it works.
However, I'm ...
4
votes
2
answers
143
views
Lift off without receiver
Can I make a small drone frame achieve lift using 4 coreless 3.7 v motors of 55000 rpm, 3.7 v lipo batteries having 40c without a receiver and remote. Motors are all alike. The propellers I have are ...
4
votes
1
answer
113
views
Is my drone battery too large?
I'm new to the drone game. I'm building an Arducopter S500,(2015) with 2212 KV920 max 1200 gram, brushless motors, 10/45 blades, SimonK ESC's, Lipo 5200 11.1V battery, and GPS 2.8. My controller is ...
4
votes
1
answer
98
views
Are drone batteries more prone to swelling than other li-ion batteries?
I have lithium ion batteries in my cell phones, laptops, portable chargers, and all sorts of devices. Sometimes I'll keep them off for a week or two and when I turn the device on, the charge may be ...
3
votes
1
answer
464
views
All motors vibrating but not spinning?
I made a 3D-printed drone body and attached some MT2204-2300kv brushless motors. I have the standard yellow 30A ESC for each of the 4 motors. I also have an Arduino Uno running YMFC-AL and a FlySky FS-...
4
votes
2
answers
1k
views
Can a 45C 11.1V 4500mah battery damage a 30A esc if a motor draws less amps?
I am really new to this, I am planning to build my own tricopter drone which can be controlled via raspberry pi using wifi and use Arduino as a flight controller to communicate via USB. I am ...
2
votes
1
answer
102
views
Questions regarding drone components
I am wanting to build an ultra-light manned bi-copter from scratch, but I first must learn about the components, which is why I am here. I am working with a 43kv (24s rated, 192 max Amp) 70kg thrust ...
3
votes
1
answer
309
views
Can you charge 1s and 2s batteries at the same time with the tinyhawk 2 included charger?
I just got a Tinyhawk 2. It came with 2 batteries (2s and 1s) and a battery charger that you plug in to USB.
I know that you can't parallel charge batteries with different cell count, but it looks ...
2
votes
0
answers
46
views
What are Pro and Cons of using Lithium batteries over LiPo batteries for quadcopters [duplicate]
I heard that some people combine some Panasonic 18650 (3400mah 3.7V) lithium batteries to make a battery for their drones, I was wondering of the advantages and disadvantages of using this type of set ...
2
votes
1
answer
130
views
Can a lipo battery be charged with more than 0.5 amps? [duplicate]
Using ISDT q8 to charge my 1205mAh 6S lipo battery. I'm wondering if I can change the default settings and charge with more amps?
Is this recommended or will it degrade the battery much quicker. Any ...