Questions tagged [creality-cr-10]
For questions about the Creality CR-10 family of 3D printers
121
questions
1
vote
1
answer
53
views
Hot end cooling fan runs when bed heater activated. Was expecting fan to run when hot end heater activated
While debugging I noticed that the hot end cooling fan did not turn on when I manually set the hot end temperature target to 200 °C. Even after the hot end reached 200 °C the fan did not turn on. The ...
3
votes
1
answer
52
views
Can I print and sell 3D models licensed under CC BY-SA?
Can I print and sell 3D models licensed under CC BY-SA? I am selling something that has a CC-BY-SA license.
0
votes
1
answer
64
views
PLA Print fail - Stringing and underextrusion
I've been printing for a few months now and most of my prints end up pretty fine, but recently this started happening:
I print on a Creality CR-10 Smart Pro with 1.75 mm PLA and a 0.4 mm nozzle at ...
0
votes
0
answers
62
views
Loose filament hairs on print
I'm printing a vase using Spiralize Outer Contour.
On each print, I run into the issue you see in the photos. There's random 'hairs' of filament spread across the print.
I think it is because there ...
0
votes
0
answers
108
views
Printer always homes X & Y at end of print
I can't figure out why, but at the end of every print, my Creality CR-10 Smart Pro will move the print head left until it hits the limit switch and move the bed back until it hits its limit switch. I ...
0
votes
1
answer
89
views
Changing axial fan on CR-10 smart caused temp fluctuation/heat creep
Printer: Creality CR-10 Smart
Slicer: Cura
My axial fan, which cools the heatsink, broke down. I replaced it with a cheap knock-off fan, as it was the only option available. However, this replacement ...
0
votes
1
answer
306
views
Extruder clogs after a while on Creality CR-10s Pro v2
The printer has been working perfectly for hundreds of prints. No issues whatsoever. Last week the extruder started clogging. It happens after printing just fine the first half hour or so (3 mm height)...
0
votes
1
answer
67
views
How to improve quality of edge over support
I am having trouble with my print here, specifically with the part laying on the green support:
It seems the edge running on the supports does not stick to it and it wants to curl upwards :
I have ...
0
votes
0
answers
62
views
Printer turns off after heating up the hotend
I have a Creality CR-10 Max. When I start heating up the hotend, it always suddenly turns off.
I did check the resistance of the heater it was about 4 Ω. The heater itself have 40 W and 24 V. So the ...
1
vote
2
answers
1k
views
Absolute Z values not 0 at print surface after auto homing with CR-Touch
I recently installed the CR-Touch onto my CR10-V3 printer. I updated my firmware to Marlin 2.1.2M and set my probe offsets and selected level bed which checked 81 points on the print bed and it said ...
0
votes
0
answers
33
views
CR-10S Pro direct drive upgrade
I am looking at getting a direct drive upgrade kit for my Creality CR-10s Pro printer (e.g. on Amazon there is one with brand name Yeebyee). My question is about whether these kits support the ...
1
vote
0
answers
604
views
How can I successfully set up my fans to run on my CR-10 using Marlin?
I have a CR-10 (original version), and I just installed an SKR E3 Mini V3.0 board, with custom Marlin firmware. Everything else seems to be running properly, but some of my fans won't spin, or won't ...
3
votes
1
answer
462
views
Replacement Extruder for CR10 Pro Smart
Is the Sprite Extruder Pro Kit the correct kit to replace my extruder on my CR 10 Pro Smart or is there another option from Creality?
2
votes
0
answers
562
views
I want to change default start position to the center of Creality CR 10 Smart Pro
Currently my 3D printer starts all projects from the lower left corner of the heatbed. I want to change the default setting to make the center of the heatbed the default position.
However, I have not ...
1
vote
0
answers
388
views
Printer hotend heating slowly and faulting
I have a CR-10max that is about 3 years old and can no longer print due to hot end faults. The hot end starts ramping up temperature but is unable to get past 150 °C, unless I turn off the hotend fan ...