All Questions
45
questions
0
votes
0
answers
313
views
Privoxy and openvpn in docker
for one project purpose I want following. On rpi I want make proxy in docker. I install privoxy and openvpn in docker. When I start docker and start privoxy, everything works normally (I configure ...
0
votes
2
answers
269
views
Limiting routing only from specific ip
Currently I run an openvpn server that pushes a route on per client basis (different clients receive different routes and static ips).
ccd/client1
push "route 172.16.236.0 255.255.255.0"
...
0
votes
1
answer
3k
views
Port Forward with dockerized OpenVPN-Server
So I am a bit new to the VPN stuff and am currently getting a little desperate.
For what I want to do. I have rented a little server somewhere (static IP, Domain and everything). Now I want to run ...
-1
votes
1
answer
749
views
How to allow VPN traffic to a Docker Container
I have the following:
Docker Host (public IP 5.6.7.8)
(1) Client (IP 1.2.3.4) <--> (2) OpenVPN in a Container (public IP 5.6.7.8, port 1194)
...
0
votes
1
answer
741
views
What is missing in this client-to-client OpenVPN setup?
I've been able to set up an OpenVPN server with several clients using static ips, the static ip is set by adding a line like ifconfig-push 192.168.254.6 192.168.255.1 in the ccd for each of the ...
1
vote
1
answer
895
views
How do I avoid IPV6 errors when trying to use kylemanna/openvpn image
I am trying to run the following deploy command...
docker run -v $OVPN_DATA:/etc/openvpn -d -p 1194:1194/udp --cap-add=NET_ADMIN kylemanna/openvpn
I get
Sysctl error for disable_ipv6, please run ...
0
votes
1
answer
1k
views
Getting OpenVPN server status failed after fully configuration on Centos 7 VPS
I am going to setup a VPN Server on Centos 7 VPS, running as Docker container. However, after installing OpenVPN and configuring it, I see the server status failed:
This is my server.conf file:
port ...
3
votes
1
answer
2k
views
Docker containers can't talk to subnets but the docker host can, how do I find where the packets are being dropped?
We have a setup where we have a docker container which needs to talk to devices on a VPN (openvpn) over ipv6. This is done by constructing a bridge between the docker networks and the tap0 interface ...
0
votes
0
answers
2k
views
How to enable TUN in Ubuntu running in a docker container
So basically I'm running an Ubuntu container in docker, with the host system running Ubuntu Server 20.4 LTS, and the container running 22.4 LTS. My intended goal is to have a container to download ...
0
votes
1
answer
6k
views
OpenVPN routing between subnets and LAN not working
I have set up an openVPN server with topology subnet.
It contains a set of subnets for clients in the region 10.0.X.X which are routed.
In the Server network there is a client (not in VPN) that runs a ...
1
vote
0
answers
25
views
Link docker container to a specific network interface [duplicate]
I am trying to start OpenVPN server for accessing resources on VPC network.
I have two network interfaces, public eth0 and VPC eth1. And an OpenVPN working in a docker container. But I want to use ...
1
vote
0
answers
185
views
How to block access to LAN through Open VPN running in Docker?
I'm running Open VPN server inside Docker on Debian 10. It works great.
The problem is the connected client now can access my devices on my local network. I would like to block all access to all VPN ...
3
votes
0
answers
960
views
How to bridge TAP device to overlay network?
I would like to allow OpenVPN users to reach all Docker containers that are part of Overlay network as if they were in the same LAN. The simplest example is 3 containers distributed on 2 hosts, and ...
1
vote
1
answer
1k
views
Ensure Docker traffic for node in Swarm exclusively passes through a VPN connection
I have two nodes in a Docker Swarm cluster. One of those nodes has an OpenVPN client connection to a VPN provider on interface tun0. My goals are,
Any services assigned to this node exclusively use ...
0
votes
1
answer
2k
views
Running an OpenVPN server in Docker on Ubuntu 20.04?
I'd like to run an OpenVPN server on my Ubuntu 20.04 server. There are plenty step-by-step guides as to how to do so (like here or there), this seems fairly straightforward process.
However instead of ...