Search Results
Search type | Search syntax |
---|---|
Tags | [tag] |
Exact | "words here" |
Author |
user:1234 user:me (yours) |
Score |
score:3 (3+) score:0 (none) |
Answers |
answers:3 (3+) answers:0 (none) isaccepted:yes hasaccepted:no inquestion:1234 |
Views | views:250 |
Code | code:"if (foo != bar)" |
Sections |
title:apples body:"apples oranges" |
URL | url:"*.example.com" |
Saves | in:saves |
Status |
closed:yes duplicate:no migrated:no wiki:no |
Types |
is:question is:answer |
Exclude |
-[tag] -apples |
For more details on advanced search visit our help page |
An electronic device that supplies electrical energy to a load. It can be AC or DC input. Typically DC output.
0
votes
Power supplies in parallel
Only two identical, fixed-voltage power supplies, which have the provision to do so, may be connected in parallel.
There is no way one could parallel two disparate supplies, one being rated 12-15V 32A …
0
votes
Using a 13.8 VDC 30-50A switching power supply on a 15A house circuit
The recommended power supply for Motorola 25-60W radios is the Motorola HPN4007D.
It's a 13.8V DC 15 A Output Switched Mode Power Supply working off 110-220V AC input.
Your 13.8V DC 30-50A Switched …
0
votes
Convert car stereo setup to run from mains supply
Normally the power consumption (W) or voltage (V) and current (A) would be furnished in the manual.
The voltage would normally be furnished as 13.8Vdc or as ranging from 11-14V or 11-16V. In any case …
1
vote
How to make circuit to reverse dc motor direction with a 12v+ trigger wire
Peter Walker's and AnalogKid's solution to the question, Need a circuit to detect if something has gone from off-on or on-off, is also valid for this question.
The timing diagram is nearly identical. …
1
vote
Shortening turn off time of a PSU output
Here's a relay-based solution.
2
votes
I have an old hand built power supply, am I missing something?
This schematic may be easier to comprehend.
3
votes
What is the power being set on power supply?
The Sonobond MH-2016 is a 1500 W Ultrasonic spot welder.
What is the power being set on the power supply?
It's the RF power limit for the job.
Case 1:
Set values
RF power limit = 3000 W
Energy = 150 …
2
votes
Looking for a switch or circuit that resets when power is lost in a 12V application?
An electromagnetic relay would be required.
Here's the schematic.
An 'engine running' contact, if available, would be the right replacement for 'ignition on'.
1
vote
Dual power supply with two different amperages
The transformer secondary voltage (12V - 0 - 12V) is too high and would require
the regulator to dissipate close to 50W for only 15W output. Should the heat-sinking not be adequate, the regulator woul …
3
votes
Power supply does not have diodes but still works
Here's a simplified version of the power supply circuit.
It's a full-wave bridge rectifier circuit for an output voltage of + 2 V and another full-wave rectifier circuit, that uses the transformer ce …
0
votes
Power supply multivibrator relay dc motor
A 555 astable could be used to control a DC motor in two ways as follows:
Alternately run and stop the motor using a low astable frequency.
Vary the motor speed through PWM control.
For the first, a …
1
vote
Can two 12v power supplies be connected together to increase the amperage power
Two identical linear regulated power supplies may be paralleled, should there be a facility to do so.
There are linear regulated power supply models which have the facility to interlink the regulated …
1
vote
Motor power supply issues causing 'judder/jitter'
It's a 12 V DC motor which draws 0.07 A on no load, 0.3 A on full load and 1.8 A when stalled.
A single phase, unfiltered DC supply using a 12 V 500 mA transformer and a 1 A bridge rectifier would be …
2
votes
Can a smart battery charger power a 12V windscreen wiper motor?
A modern, smart battery charger would be most unsuitable to run a car windshield wiper motor.
However, a simple 12V battery charger of yore, with a charging current of 3.5A or higher, would do. Such c …
0
votes
Negative ion generator scrambles with other electronic components in device, how can I put i...
Here are some suggestions.
All metal parts in the air purifier module are to be earthed. This includes the metal housing of the ionizer circuit board.
In case of need to work on the ionizer circuit, …