Questions tagged [transistors]
A transistor is a semiconductor device that can amplify signals and switch power. The types that are used most are BJT (Bipolar Junction Transistor), UJT (Unijunction Transistor), and MOSFET (FET, for Field Effect Transistor).
7,253
questions
1
vote
2
answers
82
views
Transistor switching speed
I want to be able to identify the speed of a transistor in terms of switching. Most datasheets don't indicate that but I found this transistor from ST-Electronics. Is it the maximum switching ...
0
votes
0
answers
21
views
RBL43P transistor
I have a circuit with transistor with marking: RBL43P that needs replacement. All search for datasheet was unsuccessful. Voltage to the supposed base of the transistor is about 33 volts.
Does anyone ...
1
vote
1
answer
40
views
Diagnosis and Replacement of 2N1101 transistor
I have a circuit board with 3 transistors on it, all of them are 2N1101. I'm trying to diagnose the problem with the board with the diode tester on my multimeter. I found 2 of the transistors have a ...
-2
votes
0
answers
69
views
How can I get these electronic components [closed]
How can I get these electronic components?
What is the difference between H10 ON and H30 ON?
All of them have 8201AG,NGD
1
vote
3
answers
56
views
Help with circuit analysis - Transistor, dc-motor, arduino, resistors
currently I am trying to improve my skills in electric circuits by small hobby project. I want to spin one mini dc motor, which is just spinning if the Arduino activates the flow of current with a NPN ...
0
votes
1
answer
46
views
Import transistor into LTSpice
I would like to import this transistor -> RFD16N06LE (datasheet: https://www.alldatasheet.com/datasheet-pdf/pdf/67811/INTERSIL/RFD16N06LE.html) into LTSpice; the datasheet has a PSPICE model ...
0
votes
1
answer
51
views
Finding relationship between saturation current and Vgs for MOSFET?
I would like to use a MOSFET to control a continuous current (i.e. by changing gate voltage), the specific MOSFET I want to use is RFD16N06LE (datasheet: https://www.alldatasheet.com/datasheet-pdf/pdf/...
0
votes
2
answers
30
views
Switching ON/OFF an ADC line
which electronic component could one use to switch ON/OFF several external lines for ADC?
Context:
I am working on a small project where I would like to measure 4 external voltages (0-3V range, let's ...
2
votes
2
answers
56
views
4N25 Optocoupler design
Below is a simple 4N25 optocoupler circuit that I designed in LTspice.
10 mA is flowing through the input. It works in saturation. According to the datasheet in Figure 2 (CTR-sat), it says 0.7, so the ...
0
votes
1
answer
118
views
Why does this transistor amplifier fail if Rc is greater than 50 ohms?
This simple circuit amplifies a 1 µV 50 ohm 7 MHz signal (e.g. RF off an antenna) quite nicely (31 dB):
However, I'm stumped as to why R2 must be so low (50 ohms), giving a Ic of close to 50 mA. ...
2
votes
1
answer
254
views
Is my setup for a 5V motor project faulty?
I'm trying to get a motor (5V nailbrush, no name, no specifications whatsoever) to spin for a set time and pause for a set time using a PIC10F200 microcontroller in conjunction with a 2N2222 NPN ...
6
votes
2
answers
862
views
Will this 3.3 V signal voltage be high enough to close Q3?
3 V signal (PWR-ENABLE) be enough to turn on this circuit?
The collector of Q3 will be at 11 V before switching is to occur.
Q3 Data sheet
Q1 Data sheet
2
votes
1
answer
61
views
Transistor AND gate problem
I am new to electronics and I built a simple AND gate from 2N2222 transistors. I want to use the output from the AND gate in a different circuits not just an LED but maby an OR gate. Can someone tell ...
0
votes
3
answers
121
views
Power dissipation in an IC
Here is LM741 op amp circuit in Figure 1. The amplifier has two power supplies \$V_{cc}\$ and -\$V_{ee}\$. The up arrows are connected to the positive power supply \$V_{cc}\$ which is +15 V. Current ...
2
votes
4
answers
310
views
Why is a push-pull transistor configuration asymmetric?
Looking at the circuit below:
How do I analyze it? Specifically, why is the output able to go nearly all the way to +12 V but not beneath 0 V? I'd expect that when V(sig) < 0, since current flows ...