Skip to main content

All Questions

Tagged with
0 votes
1 answer
102 views

Connection of two devices

I need to design an Ethernet interface. Requirements: It should have two RJ45 connectors at 1Gbps data rate and two fiber-optic at 1Gbps rate. The system has two SoMs (Kria K26) and each one should ...
user avatar
1 vote
0 answers
86 views

Unable to get frequency on oscilloscope

I am using NOR flash IS25WP256D in my project. I configured a frequency of 80 MHz and a bus width of 4 in DTS, but when I observed with an oscilloscope I got 62 MHz. Why does this happen? These are ...
Chithra M G's user avatar
1 vote
1 answer
1k views

What is the difference between Bare metal, RTOS and SoC? [closed]

Having just recently gotten into embedded programming using PIC microcontrollers, I am trying to understand the difference between Bare metal, RTOS and SoC. Online searches reveal contradictory ...
aLoHa's user avatar
  • 597
0 votes
2 answers
230 views

Programmable Microcontrollers vs. SoC Devices [closed]

Context: I essentially don't have a strong electrical engineering background. My knowledge consists in playing around with Arduino based microcontrollers or Raspberry Pis or equivalent SoCs. Question:...
image357's user avatar
  • 101
0 votes
1 answer
214 views

Is there a SoC for IoT with cellular network, Wi-Fi, Bluetooth? [closed]

I am looking for SoC with support for cellular network, Wi-Fi and Bluetooth. In fact, any Mediatek is suitable, but I am an individual and no one will sign an agreement with me, I suppose. Yes, and I ...
serko's user avatar
  • 3
0 votes
0 answers
39 views

CC541 microcontroller

I am trying to use the SoC CC2541 which is from Texas Instruments and is mounted with an 8051 mcu. I know that the firmware can be flashed through an Arduino board but as I want to avoid using an ...
GGChe's user avatar
  • 91
1 vote
1 answer
337 views

Adding Ethernet ports to my SoC

I'd like to add multiple (>5) Ethernet ports to a board I am developing. Linux on the CPU has to see each port individually, be able to route the traffic among ports, and also add traffic on its own (...
RH6's user avatar
  • 25
0 votes
3 answers
227 views

From microcontrollers to microprocessors [Embedded Devices] [closed]

I was told by some developer that embedded controllers are task specific devices that requires low latency which processor based devices can't offer due to OS overhead. So I would like to first of ...
GENIVI-LEARNER's user avatar
1 vote
2 answers
609 views

How can I program an SOC without a hardware kit?

I am new to the production side of electronics. I was wondering if I can directly use a DA14683 to implement a size-constrained project. I have a few queries in mind Is interfacing a SOC similar to ...
Bruce_wayne's user avatar
0 votes
1 answer
970 views

PLDs, DSPs, MCUs, MPUs and SoCs Typical Application [closed]

PLDs, DSPs, MCUs, MPUs and SoCs are all embedded devices, they can be programmed / configured to achieve a specific application. I've worked with MCUs and FPGAs in the past and realized that they are ...
A.Lacasse's user avatar
0 votes
2 answers
154 views

Can SoC Processors be used as more powerful microcontrollers? [closed]

I'm starting with microcontrollers (still avr), and once I finish, I'll be moving on to ARM based microcontrollers. However, as I've been reading, the ARM Cortex M is basically the best you can get, ...
Poria Amirian's user avatar
1 vote
1 answer
450 views

How to program SoC chips like CC2541F128RHAT [closed]

I am working on a BLE project. As per initial research, decided to use the cc2541 chip as BLE module. I have found one here. As per the datasheet, it shows it contains BLE and MCU. I need to program ...
McLosys Creative's user avatar
1 vote
1 answer
115 views

using smartphones SOC or other components as microcontroller like arduino [closed]

i have a smartphone which has stuck in boot loop,i was just wondering if i could use it's internal components like SOC to use it as microcontroller like "arduino".have anyone ever tried it?or possess ...
yin yang's user avatar
1 vote
2 answers
182 views

How to use a reference design in datasheet?

I'm trying to gain a better understanding on what this is and how to use it. I know this is a datasheet for SAMB11 SoC, more specifically the reference design on page 50 is what I'm inquiring about. ...
Niko_Jako's user avatar
-3 votes
1 answer
102 views

What thing should be consider while choosing BLE uC [closed]

I'm newbie in BLE segment need micro-controller with bluetooth (SOC). Please help me what thing should be consider while choosing SOC.
Jon's user avatar
  • 45

15 30 50 per page