All Questions
Tagged with lipo lithium-ion
46
questions
8
votes
2
answers
1k
views
Power bank or fire hazard?
I do have a bunch of 18650 LiPo cells, salvaged from various sources. Now, I happened to come across a variety of power bank cases on Amazon which mostly look like this:
Even a cursory look tells me ...
1
vote
1
answer
70
views
Can I use a MAX17262 to measure battery capacity of a 300mA 3.7V Lipo?
First, I a very basic understanding of lithium based batteries and from what I have learned, gauging their capacity can be quite complex. I was looking into MAX17262 as a fuel gauge to measure the ...
1
vote
2
answers
49
views
Specific Li-po, Li-ion and charging facts (low intensity, slow)
I have the following battery, but not its original charger:
12 V, 4.0 Ah
Cell Balancing Longer Battery Life Increased Battery Lifespan. Higher Battery Resources Due To Evenly Used Cells.
BTW ...
0
votes
1
answer
438
views
Is my 2S Lipo charger design with bypass while charging correct? Need some help on isolating the charger from the battery while not charging!
I'm using a circuit to charge a 2S lipo battery, and bypass the battery while it's charging, and still supply energy the circuit.
It works. But for the new charger module I'll use now, when the ...
15
votes
4
answers
3k
views
Why is charging with Lithium batteries with a small load dangerous?
I'm well aware of the best practices for charging lithium chemistry batteries, and how the charges themselves work.
I've never had a water tight explanation on why having a load on a battery during ...
-1
votes
2
answers
985
views
Connecting 3 Li-ion pouch cells in series with BMS
I have three 2000 mAh, 3.7 V Li-ion pouch cells.
I want to connect these three cells in series to get 11.1 V and 2000 mah
I made 11.1 V out of three Li-ion cylinder cells before; I used a BMS.
As my ...
0
votes
1
answer
253
views
Inconsistent battery level reading on ESP32
We have a IOT design that runs its normal operation with 12 V DC. Without the 12 V DC, we have a 2-cell Li-ion battery pack which outputs 6-8.4 V.
As a Li-ion charger we use Microchip's MCP73213.
We ...
0
votes
1
answer
123
views
Charging a LiPo using Battery Protection Circuit
I have an application where I power an ESP32 from a LiPo battery. Between the LiPo and the ESP32, I have a DW01A battery protection circuit (data sheet is here: https://hmsemi.com/downfile/DW01A.PDF).
...
0
votes
1
answer
115
views
Using a rechargeable LiPo/Li-ion battery as "burst" current source
For a project I'm working on, I need to run a motor for a few seconds (somewhat rarely). The motor requires 24V@1A. The rest of the circuitry runs on 3.3V@300mA. My general thought is to use a 3.7V ...
0
votes
0
answers
756
views
How can I use 2 TP4056 to safely discharge 2 18650 cells in series
I am new to electronics. I have made a robotic car type thing with arduino and L298N and I want to power it using two 18650 ...
1
vote
1
answer
1k
views
Li-ion vs Li-Po batteries cut-off protection
I am confused with the differences between Li-ion batteries (like 18650) and Li-Po (the flat ones).
I know that basically they are both lithium ion, but when I want to buy I see that LiPos have always ...
0
votes
2
answers
466
views
Is charging current shared between Separate LiPo batteries wired in parallel?
I have two separate 2000mAh LiPo batteries (not RC type the standard 2 wire DIY component type https://coolcomponents.co.uk/products/lithium-polymer-battery-2000mah) Which I want to wire in parallel ...
1
vote
1
answer
36
views
Should there be a clearance between a lithium polymer cell and a charging circuit?
I'm building a compact portable console that is going to use a 500ma charger board from Adafruit and possibly a 5v 1a boost as well. Past experience has taught me the chips on those little circuit ...
0
votes
0
answers
1k
views
How to tell a battery is LiPo or Li Ion (based on apperance)?
I have this battery and I don't know it is lipo or li-ion:
Is there any way to tell a battery is lipo or li-ion based only on apperance?
0
votes
1
answer
2k
views
Make 9v ups for router with TP4056 and MT3608
I am building 9v UPS for my wifi router using TP4056 lithium-ion charging module and MT3608 stepup converter. If USB power is available I want MT3608 to get power from USB (TP4056 Vin Pin) otherwise ...