All Questions
Tagged with impedance-matching transformer
20
questions
0
votes
2
answers
113
views
Impedance matching transformer simulation
Here is an example of a transformer that converts 10Ohm load into 1kOhm
And the AC simulation result
From my understanding the source sees the transformer as an inductor in parallel with a converted ...
1
vote
0
answers
293
views
Designing of a ribbon microphone (sort of) output transformer
I'm currently working on an experimental string musical instrument. It isn't my invention though. The source of inspiration called Dvina has an unusual pickup system. It senses the current induced in ...
1
vote
0
answers
109
views
How to match Transformer output Impedance for Ultrasonic Cleaning Transducer
I have a transformer outputting the 240VAC 40kHz. The Transducer is 50W, 4100pF, 10-20 Ohm at resonance, ~40kHz resonance)
The Secondary of the transformer is 12mH.
I am trying to match the impedance ...
1
vote
1
answer
117
views
Is this an Impedance Matching Curve?
This may be a very quick answer, I had a test that was set up like this. The primary inductance of the transformer was roughly 0.022H and the inductance of the secondary of the transformer was 0.045H. ...
3
votes
0
answers
173
views
Eliminate reflections on pulse signal transformer
I am trying to isolate an RLC ringdown signal via an RF signal transformer but I'm having trouble maintaining the signal integrity through the transformer. Below is the simple schematic describing my ...
2
votes
0
answers
44
views
Keep potential difference fixed for transformer's output
I have a source consisting of V1, R1, L1, and L2 to which my load R2 is attached:
For the load, I have 10 or 100 Ohms.
1) R2 = 10 Ohms: Vrms = 315 V, irms = 32 A, P = 10 kW
2) R2 = 100 Ohms: Vrms =...
8
votes
4
answers
1k
views
What is an audio output transformer? Is it the same thing as an impedance matching transformer?
What is meant by an audio output transformer, does it mean that it is designed to operate at audio frequency or to match impedance?
2
votes
2
answers
448
views
What is the impedance of a multi-tap impedance matching transformer when all taps are used at the same time?
So if I have an impedance matching transformer with two taps, one 8ohm and the other 4ohm, and both taps have a winding relationship so that the other side "sees" a 4kohm load, what is the impedance ...
0
votes
2
answers
159
views
What are the fixed values in transformer?
I am trying to understand how impedence matching works, but I realized I had some issues with basic transformers as well:
If the voltage and current is merely dependent to the input voltage, current ...
8
votes
3
answers
2k
views
Audio transformer: What to do with an unused winding?
For the purpose of impedance matching and floating a single-ended, ground-referenced signal, I am planning to use an audio transformer like this one.
Here's the schematic from the data sheet:
My ...
1
vote
2
answers
4k
views
Transformers and impedance matching
What I have learned: In a ideal transformer, the power in the primary circuit will equal the power out in the secondary circuit.
Impedance matching: if I take the turns ratio of the transformer in ...
0
votes
1
answer
708
views
Amplifier impedance matching with constant voltage speaker systems
I understand that in order not to potentially overload an amplifier one should connect a speaker with an impedance no less than that specified, and I have just recently come to understand that for ...
1
vote
1
answer
2k
views
Impedance matching with transformer and resistor
I want to drive a 8Ohm load with a tube amp(Push-pull 2xEL84) that needs a ~8kOhm impedance on its outputs.
I have a transformer that has a impedance turns ratio of 0,048. link
So if I just plug in ...
0
votes
1
answer
384
views
Noise Matching transformer [closed]
I'd like to use a transformer to improve the performance of our SR5184 preamp.
The signal recovery SR5184 is an ultra low noise preamplifier. It has 0.8 nV/ √Hz input noise and a bandwidth of 0.5 Hz -...
2
votes
2
answers
1k
views
Impedance matching audio transformer windings
I want to create an isolation, impedance matching, balancing transformer for a DI box.
I want it to work on Audio frequency and use a toroidal ferrite core.
The input is an electric guitar, so it ...