All Questions
Tagged with buck-boost lithium-ion
11
questions
0
votes
1
answer
41
views
Automobile 12V UPS circuit with Li ion battery
Currently I have a battery backup circuit for a GPS device to run on automobile power source and I am trying to improve a few things. Any help is appreciated.
Currently I am facing issues of negative ...
0
votes
0
answers
27
views
Enable/Disable Power of Board with ESP32-S3
I am using TPS63001 Buck-Boost Coverter with a 3.7 Li-Ion Recharable battery. I want to Control Power of the board with ESP32-S3-Mini. Enable pin of the TPS63001 is connected to MCU and its also ...
0
votes
0
answers
69
views
Charging IC for a 1S or 3S Li-ion battery
I have quite specific problem; I'm designing a PCB for my robot, that is used the main board for controlling motors, gathering data from sensors, etc.
The whole PCB will be designed as a Raspberry Pi ...
1
vote
1
answer
30
views
Li-Ion Battery Array: V.out ≥ 3.5 [V], I.out ≤ 1 [A] : No voltage regulation? Boost? BuckBoost? SeriesxParallel — 1x4? 2x2?
With a lithium ion cell array as follows:
n.cell = 4.0 [-]
V.cell.max = 4.2 [V]
...
- 437
0
votes
0
answers
101
views
Powering 12 V LED strips via a 3S lithium ion battery pack in a tight compartment
I am working on a project for an LED lamp. We are trying to power it via a 3S lithouk ion battery pack delivering up to 12.6 V with a cutoff voltage of 9 V. The brightness of the LEDs at 10.5 V is the ...
- 1
1
vote
1
answer
130
views
How to connect in serial two 2S Battery pack but charge them seperately?
I want to create a circuit that has input 12V DC and uses this voltage both charging two 2S (7.4V Li-Ion without balancing wire with BMS Circuit on the pack) batteries and at the same time supplying ...
- 44
0
votes
0
answers
66
views
Charging and discharging Li-ion cell dynamically
I intend to use an EBL 6F22 5400 mWh, 9 V Li-ion block as buffer for an USB-level solar charging station.
It comes with a micro-USB charging slot and necessary voltage regulation. Not much can be ...
1
vote
1
answer
94
views
simple DCDC Step Up converter mystery
I'm designing a self sustaining guitar that has 6 amplifiers onboard and runs on a li-ion pack.
Power draw is a about 2.5A when on "full power" and I decided to make my own step up converter ...
- 37
3
votes
2
answers
448
views
Buck/Boost converter interaction with MCU in sleep mode?
I am trying to design a battery powered remote controller that has the following components, TPS63802 (converter), AP9211 (battery charger/protection), Atmega328 (MCU), NRF24 (transceiver). The ...
0
votes
0
answers
32
views
Dedicated li-ion step up drivers
I have a design which will include the optional use case of boosting up to 7V from a li-ion battery.
I can't seem to find any drivers dedicated to li-ion for this? There seem to be a few buck boost ...
- 757
0
votes
1
answer
175
views
Can I use dc-to-dc converter to step up voltage of 20 3.7V 3Ah lithium-ion batteries connected in parallel?
I want to use this 3.7V 40Ah powerbank to power my e bike's 48V hub motor. So would it be a bad idea to step up 3.7V all the way up to 48V? Would there be a huge Ah loss?
- 19