Unanswered Questions
59 questions with no upvoted or accepted answers
5
votes
0
answers
3k
views
SRAM XD cassette will not fit on the splines of an XDR driver
I have an 11 speed 10-42 XD cassette that I am trying to fit on an XDR driver (this one - https://www.alltricks.com/F-41493-pieces-roues/P-676097-fulcrum_body_sram_xdr). No matter how I turn the ...
4
votes
0
answers
279
views
Sram AXS derailleur does not shift
Have you encountered a problem where a rear AXS derailleur stops shifting? Any suggestions?
I bought a mint 2023 GX AXS derailleur on Marketplace, it worked for the first short test ride on a road but ...
- 141
3
votes
0
answers
141
views
New hub slipping when powering up?
I recently had my Giant Propel SLR serviced (including new chain, Cassette and a new Hub) as gears were beginning to slip. However after the service when I climb into top / hardest gear and put the ...
3
votes
0
answers
96
views
Can't find a "friction screw" for a friction shifting system
I recently broke one of the two speed levers ajuster (friction screw) that adjust the pressure between the levers and the cable. It's made in plastic as shown in the picture below. I would like to ...
- 31
3
votes
1
answer
2k
views
What are the axle nut sizes on the brompton?
What are the exact specifications of the nuts used on the various axles of the Brompton bicycle?
Specifically, I have a 2016 M6R black, but I would appreciate it if you listed the specifications for ...
CommunityBot
- 1
2
votes
0
answers
33
views
How can I make my vintage sturmey Archer AW hub take a 3 speed cassette? (Minimal metal work, none if possible)
So to make answering my question easier, I'll start with the goals, I wish to be able to attach a 3 speed cassette and tensioner (relatively low cost) to my vintage Sturmey Archer AW hub so i can have ...
2
votes
0
answers
50
views
Something like chainsuck on RD lower pulley after new crankset install?
I just switched out a Shimano M5100 crankset for a SRAM GX Eagle crankset. I am using a KMC X11-EL chain. I cleaned the chain before installing it with the new crankset. My RD is a Shimano SLX 11-...
- 2,090
2
votes
0
answers
101
views
Look at my trike
About 21 days ago exactly I posted for help identifying some junk in a barn.
Today i can show you what these parts were supposed to look like.
I've figured out a bunch during the process.
The lever ...
- 31
2
votes
0
answers
95
views
Cable housing end cap for BR-M375
I replaced the no name brake calipers on an entry-level ebike for Shimano BR-M375. The cable housing for the rear caliper was a bit too long, so I cut off a few centimeters. Then, I put a new 5 mm end ...
- 4,159
2
votes
1
answer
243
views
Upgrading Shimano Acera 8 speed Rear Derailleur to 8 speed Shimano XTR derailleur
Looking for some help here. I am upgrading Shimano Acera 8 speed rear derailleur to 8 speed Shimano XTR rear derailleur and it appears that because the old 8 speed XTR derailleur has a clip for the ...
CommunityBot
- 1
2
votes
0
answers
60
views
clicking chain on 3rd gear only
Shimano DI2 11 speed XTR on my gravel bike. The 3rd from smallest gear on the cassette makes a clicking sound. Any other gear its fine. Cassette and chain are fairly new. Have reindexed, checked ...
- 21
2
votes
0
answers
78
views
How are these rack and mudguard holders named?
How are these parts holding the rack and the mudguards named in English? There are some pictures on the web featuring "parts of the bicycle" but they are not depicted there with names. This ...
- 7,899
2
votes
0
answers
416
views
Using 11-36t 9 speed derailleur with 11-40t 9 speed cassette
So I've got the shimano altus rd-m2000 and it says that it only supports 11-36t. However, I've seen people on forums say that it's possible with this derailleur. Even it I was wondering if with a ...
- 21
2
votes
0
answers
421
views
chain / cassette / chainrings replacement ratios - how often to you usually replace cassettes & chainrings per number of replaced chains?
I'm looking to get other riders experiences with how often cassettes and chainrings usually have to be replaced per the number of chain replacements. On my 2 road bikes I usually find roughly the ...
- 887
2
votes
0
answers
835
views
Why do SRAM rear derailleur not have a parallel movement
My SRAM rear derailleur (Rival 22 circa 2016) has a non parallel movement. When it is in the lowest gear, the cage and pulley sprockets align with the cassette sprockets, but when it's in the highest ...
