Unanswered Questions
66 questions with no upvoted or accepted answers
6
votes
0
answers
109
views
What is forward drag on a coaster brake
I have a single-gear coaster brake bicycle that needed fixing. I would have to pedal real hard to get it to go and backpedal a block in advance for bike to stop. Very spongy brakes. Well I took brake ...
5
votes
0
answers
3k
views
SRAM XD cassette will not fit on the splines of an XDR driver
I have an 11 speed 10-42 XD cassette that I am trying to fit on an XDR driver (this one - https://www.alltricks.com/F-41493-pieces-roues/P-676097-fulcrum_body_sram_xdr). No matter how I turn the ...
4
votes
0
answers
279
views
Sram AXS derailleur does not shift
Have you encountered a problem where a rear AXS derailleur stops shifting? Any suggestions?
I bought a mint 2023 GX AXS derailleur on Marketplace, it worked for the first short test ride on a road but ...
4
votes
0
answers
125
views
Scott 965 hub Problem
Good afternoon, I recently bought a Scott 965, I chose this bike for the beauty of it and the equipment it came with, I wanted to change to a bike with sealed bearings and leave the bearings Sphere ...
3
votes
0
answers
141
views
New hub slipping when powering up?
I recently had my Giant Propel SLR serviced (including new chain, Cassette and a new Hub) as gears were beginning to slip. However after the service when I climb into top / hardest gear and put the ...
2
votes
0
answers
33
views
How can I make my vintage sturmey Archer AW hub take a 3 speed cassette? (Minimal metal work, none if possible)
So to make answering my question easier, I'll start with the goals, I wish to be able to attach a 3 speed cassette and tensioner (relatively low cost) to my vintage Sturmey Archer AW hub so i can have ...
2
votes
0
answers
50
views
Something like chainsuck on RD lower pulley after new crankset install?
I just switched out a Shimano M5100 crankset for a SRAM GX Eagle crankset. I am using a KMC X11-EL chain. I cleaned the chain before installing it with the new crankset. My RD is a Shimano SLX 11-...
2
votes
1
answer
243
views
Upgrading Shimano Acera 8 speed Rear Derailleur to 8 speed Shimano XTR derailleur
Looking for some help here. I am upgrading Shimano Acera 8 speed rear derailleur to 8 speed Shimano XTR rear derailleur and it appears that because the old 8 speed XTR derailleur has a clip for the ...
2
votes
0
answers
60
views
clicking chain on 3rd gear only
Shimano DI2 11 speed XTR on my gravel bike. The 3rd from smallest gear on the cassette makes a clicking sound. Any other gear its fine. Cassette and chain are fairly new. Have reindexed, checked ...
2
votes
0
answers
1k
views
DT Swiss 370 hub not spinning smoothly in thru axle frame (end caps?)
I have a brand new rear wheel that uses a DT Swiss 370 hub. (From what I understand, the 370 is the same as the 350 except with pawls instead of a ratchet.) I'm trying to use it on a 12x142 thru axle ...
2
votes
0
answers
416
views
Using 11-36t 9 speed derailleur with 11-40t 9 speed cassette
So I've got the shimano altus rd-m2000 and it says that it only supports 11-36t. However, I've seen people on forums say that it's possible with this derailleur. Even it I was wondering if with a ...
2
votes
0
answers
170
views
What does the brake adjuster nut do? Sturmey Archer S2C coaster brake hub
Looking at the schematics of the sturmey archer S2C hub I noticed this part:
2 HMN425 Brake Adjuster Nut (Xylan)
And I was wondering, what does it exactly adjust? Does it adjust the brake ...
2
votes
0
answers
421
views
chain / cassette / chainrings replacement ratios - how often to you usually replace cassettes & chainrings per number of replaced chains?
I'm looking to get other riders experiences with how often cassettes and chainrings usually have to be replaced per the number of chain replacements. On my 2 road bikes I usually find roughly the ...
2
votes
0
answers
835
views
Why do SRAM rear derailleur not have a parallel movement
My SRAM rear derailleur (Rival 22 circa 2016) has a non parallel movement. When it is in the lowest gear, the cage and pulley sprockets align with the cassette sprockets, but when it's in the highest ...
2
votes
1
answer
1k
views
Compatibility of Shimano Ultegra and Sora components
My road bike has an Ultegra groupset, but some parts need replacement (chainrings, chain, and cassette). The chain is worn out, the cassette is sliding with a new chain, and the chainset is also worn ...