Unanswered Questions
65 questions with no upvoted or accepted answers
6
votes
0
answers
109
views
What is forward drag on a coaster brake
I have a single-gear coaster brake bicycle that needed fixing. I would have to pedal real hard to get it to go and backpedal a block in advance for bike to stop. Very spongy brakes. Well I took brake ...
- 13.9k
4
votes
0
answers
278
views
Sram AXS derailleur does not shift
Have you encountered a problem where a rear AXS derailleur stops shifting? Any suggestions?
I bought a mint 2023 GX AXS derailleur on Marketplace, it worked for the first short test ride on a road but ...
- 141
4
votes
0
answers
125
views
Scott 965 hub Problem
Good afternoon, I recently bought a Scott 965, I chose this bike for the beauty of it and the equipment it came with, I wanted to change to a bike with sealed bearings and leave the bearings Sphere ...
CommunityBot
- 1
3
votes
0
answers
141
views
New hub slipping when powering up?
I recently had my Giant Propel SLR serviced (including new chain, Cassette and a new Hub) as gears were beginning to slip. However after the service when I climb into top / hardest gear and put the ...
3
votes
1
answer
2k
views
What are the axle nut sizes on the brompton?
What are the exact specifications of the nuts used on the various axles of the Brompton bicycle?
Specifically, I have a 2016 M6R black, but I would appreciate it if you listed the specifications for ...
CommunityBot
- 1
2
votes
0
answers
50
views
Something like chainsuck on RD lower pulley after new crankset install?
I just switched out a Shimano M5100 crankset for a SRAM GX Eagle crankset. I am using a KMC X11-EL chain. I cleaned the chain before installing it with the new crankset. My RD is a Shimano SLX 11-...
- 2,090
2
votes
1
answer
243
views
Upgrading Shimano Acera 8 speed Rear Derailleur to 8 speed Shimano XTR derailleur
Looking for some help here. I am upgrading Shimano Acera 8 speed rear derailleur to 8 speed Shimano XTR rear derailleur and it appears that because the old 8 speed XTR derailleur has a clip for the ...
CommunityBot
- 1
2
votes
0
answers
60
views
clicking chain on 3rd gear only
Shimano DI2 11 speed XTR on my gravel bike. The 3rd from smallest gear on the cassette makes a clicking sound. Any other gear its fine. Cassette and chain are fairly new. Have reindexed, checked ...
- 21
2
votes
0
answers
1k
views
DT Swiss 370 hub not spinning smoothly in thru axle frame (end caps?)
I have a brand new rear wheel that uses a DT Swiss 370 hub. (From what I understand, the 370 is the same as the 350 except with pawls instead of a ratchet.) I'm trying to use it on a 12x142 thru axle ...
- 264
2
votes
0
answers
416
views
Using 11-36t 9 speed derailleur with 11-40t 9 speed cassette
So I've got the shimano altus rd-m2000 and it says that it only supports 11-36t. However, I've seen people on forums say that it's possible with this derailleur. Even it I was wondering if with a ...
- 21
2
votes
0
answers
170
views
What does the brake adjuster nut do? Sturmey Archer S2C coaster brake hub
Looking at the schematics of the sturmey archer S2C hub I noticed this part:
2 HMN425 Brake Adjuster Nut (Xylan)
And I was wondering, what does it exactly adjust? Does it adjust the brake ...
- 121
2
votes
0
answers
835
views
Why do SRAM rear derailleur not have a parallel movement
My SRAM rear derailleur (Rival 22 circa 2016) has a non parallel movement. When it is in the lowest gear, the cage and pulley sprockets align with the cassette sprockets, but when it's in the highest ...
2
votes
0
answers
95
views
What size rear axle and cones for 1999 Schwinn Cruiser 6?
What size rear axle and cones fit a 1999 Schwinn Cruiser 6 bicycle. I cannot find a part number or identifier, is it the same size as BMX parts?
- 75.8k
2
votes
1
answer
98
views
Old bike: replaced rear axle but the tire goes off the axis when I get on it
I just broke and then replaced my rear axle on an old timey race bike I bought online.
Everything seems to go smoothly when the bike is up on a stand or on at my side, but once I get on it and try to ...
- 47
2
votes
1
answer
4k
views
Identifying Rear Axle Size
I've got a bent QR rear axle and am looking for a replacement. Seems that these come in 9.5 and 10 mm sizes with a couple of different threadings. When I measure the OD of the threads I get around 9.8 ...
- 3,896