Unanswered Questions
66 questions with no upvoted or accepted answers
4
votes
0
answers
278
views
Sram AXS derailleur does not shift
Have you encountered a problem where a rear AXS derailleur stops shifting? Any suggestions?
I bought a mint 2023 GX AXS derailleur on Marketplace, it worked for the first short test ride on a road but ...
- 141
3
votes
0
answers
70
views
How to properly adjust front derailleur height when it can sway significantly once the clamp bolt is loosened up?
I'm trying to adjust derailleurs myself, for the first time .)
the model is DEORE XT
following the how-to
https://www.wikihow.com/Adjust-a-Shimano-Front-Derailleur
the very first step - adjusting its ...
3
votes
0
answers
67
views
Are there compatibility restrictions about remotes for dropper posts and suspension locks?
I consider adding an handle bar remote for a bike with a front-suspension fork. Given the bike has already a dropper post, I was thinking to add a dual "dropper/suspension" remote.
I noticed ...
- 21.4k
2
votes
1
answer
74
views
Sram/Avid brake hose compatiblity
I have Sram Rival AXS which I want to transfer from one bike to another. Unfortunately the new bike is bigger (M -> XL) so new brake hose is required. SRAM recommends SRAM Brake Hose Kit - Double ...
CommunityBot
- 1
2
votes
0
answers
50
views
Something like chainsuck on RD lower pulley after new crankset install?
I just switched out a Shimano M5100 crankset for a SRAM GX Eagle crankset. I am using a KMC X11-EL chain. I cleaned the chain before installing it with the new crankset. My RD is a Shimano SLX 11-...
- 2,090
2
votes
0
answers
95
views
Cable housing end cap for BR-M375
I replaced the no name brake calipers on an entry-level ebike for Shimano BR-M375. The cable housing for the rear caliper was a bit too long, so I cut off a few centimeters. Then, I put a new 5 mm end ...
- 4,159
2
votes
1
answer
243
views
Upgrading Shimano Acera 8 speed Rear Derailleur to 8 speed Shimano XTR derailleur
Looking for some help here. I am upgrading Shimano Acera 8 speed rear derailleur to 8 speed Shimano XTR rear derailleur and it appears that because the old 8 speed XTR derailleur has a clip for the ...
CommunityBot
- 1
2
votes
0
answers
60
views
clicking chain on 3rd gear only
Shimano DI2 11 speed XTR on my gravel bike. The 3rd from smallest gear on the cassette makes a clicking sound. Any other gear its fine. Cassette and chain are fairly new. Have reindexed, checked ...
- 21
2
votes
0
answers
118
views
Pirelli tires (mixing 700X23c and 70025c)
A bike shop (whom I trust) replaced my tires with new 700X25c Pirelli P Zero Zello 4S front and rear, the rear tire did not clear the fork/frame for some reason, they switched the rear 700X25c with ...
- 21
2
votes
0
answers
141
views
Rear wheel not centred
I've been trying to fit a second rear wheel to a fracing frame rebuild and I've noticed it is very off-centre. You can see from the pictures that it is much closer to the non-drive side than drive ...
- 591
2
votes
0
answers
514
views
Cane Creek "universal" hoods and Shimano 600 (BL-6400) lever compatibility
Does anyone happen to know know if these Cane Creek "universal" hoods are compatible with these vintage Shimano 600 (BL-6400) levers?
It's okay if they don't fit quite perfectly or if I have ...
- 128k
2
votes
0
answers
60
views
Clarification needed on hydraulic disc caliper and lever compatibility
I have a Scott Solace road bike that uses Shimano BR-RS805 hydraulic disc calipers. The hose spec is BH 59. I want to change from drop handlebars to Jones H handlebars. I will need new brake levers. ...
CommunityBot
- 1
2
votes
0
answers
416
views
Using 11-36t 9 speed derailleur with 11-40t 9 speed cassette
So I've got the shimano altus rd-m2000 and it says that it only supports 11-36t. However, I've seen people on forums say that it's possible with this derailleur. Even it I was wondering if with a ...
- 21
2
votes
0
answers
835
views
Why do SRAM rear derailleur not have a parallel movement
My SRAM rear derailleur (Rival 22 circa 2016) has a non parallel movement. When it is in the lowest gear, the cage and pulley sprockets align with the cassette sprockets, but when it's in the highest ...
2
votes
1
answer
1k
views
Compatibility of Shimano Ultegra and Sora components
My road bike has an Ultegra groupset, but some parts need replacement (chainrings, chain, and cassette). The chain is worn out, the cassette is sliding with a new chain, and the chainset is also worn ...
CommunityBot
- 1