Unanswered Questions
42 questions with no upvoted or accepted answers
4
votes
0
answers
279
views
Sram AXS derailleur does not shift
Have you encountered a problem where a rear AXS derailleur stops shifting? Any suggestions?
I bought a mint 2023 GX AXS derailleur on Marketplace, it worked for the first short test ride on a road but ...
3
votes
0
answers
70
views
How to properly adjust front derailleur height when it can sway significantly once the clamp bolt is loosened up?
I'm trying to adjust derailleurs myself, for the first time .)
the model is DEORE XT
following the how-to
https://www.wikihow.com/Adjust-a-Shimano-Front-Derailleur
the very first step - adjusting its ...
2
votes
0
answers
50
views
Something like chainsuck on RD lower pulley after new crankset install?
I just switched out a Shimano M5100 crankset for a SRAM GX Eagle crankset. I am using a KMC X11-EL chain. I cleaned the chain before installing it with the new crankset. My RD is a Shimano SLX 11-...
2
votes
1
answer
243
views
Upgrading Shimano Acera 8 speed Rear Derailleur to 8 speed Shimano XTR derailleur
Looking for some help here. I am upgrading Shimano Acera 8 speed rear derailleur to 8 speed Shimano XTR rear derailleur and it appears that because the old 8 speed XTR derailleur has a clip for the ...
2
votes
0
answers
60
views
clicking chain on 3rd gear only
Shimano DI2 11 speed XTR on my gravel bike. The 3rd from smallest gear on the cassette makes a clicking sound. Any other gear its fine. Cassette and chain are fairly new. Have reindexed, checked ...
2
votes
0
answers
141
views
Rear wheel not centred
I've been trying to fit a second rear wheel to a fracing frame rebuild and I've noticed it is very off-centre. You can see from the pictures that it is much closer to the non-drive side than drive ...
2
votes
0
answers
233
views
Left shifter is not catching/gets stuck when there is cable tension
I need help with my left shifter. When I have the cable attached to the derailleur and have even the slightest tension applied, the shifter won't shift to the largest cog (I have double front ...
2
votes
0
answers
416
views
Using 11-36t 9 speed derailleur with 11-40t 9 speed cassette
So I've got the shimano altus rd-m2000 and it says that it only supports 11-36t. However, I've seen people on forums say that it's possible with this derailleur. Even it I was wondering if with a ...
2
votes
0
answers
835
views
Why do SRAM rear derailleur not have a parallel movement
My SRAM rear derailleur (Rival 22 circa 2016) has a non parallel movement. When it is in the lowest gear, the cage and pulley sprockets align with the cassette sprockets, but when it's in the highest ...
2
votes
1
answer
174
views
Saddle adjustment
I was given a used specialized rock hopper last year but the seat angle is too high in the front. I've loosened the hex sockets beneath the saddle to adjust the angle but it always screws back in the ...
1
vote
0
answers
12
views
How do you stop the rubber shield from wandering unless you lock it behind the shift outer cap w/ tongue, which introduces a compressible sheath?
I installed the two parts
shift outer cap with long tongue, and
rubber shield
as shown below, but I'm not absolutely sure this is right.
If I put the rubber shield (the one on the right in the ...
1
vote
0
answers
35
views
Shimano Alifine 8 IGH yellow dots will NOT line up
With shifter in 4th gear, per instructions, the upper yellow dot is about 3/16" ahead (clockwise) of the lower yellow dot. Whether I adjust the barrel connector (at the shifter) to one extreme or ...
1
vote
0
answers
49
views
New tire tube and grinding noise?
I punctured my tire tube so i had to remove my back wheel out and replaced the tube, when reassembled, derailleurs started making grinding noises.
I checked where the sound was coming and it was ...
1
vote
0
answers
34
views
Knaap AMS 250 w bafang rear hub motor
Hi can anyone tell me if I slice this 8-pin cable that comes out of the controller so that I could connect a 5-pin display by matching color to color? I am not sure what all the 8 wires are for in ...
1
vote
0
answers
72
views
Not able to shift from a specific gear
I have a 9-speed rear derailleur and shifting from 1 to 9 isn’t a problem except when it is from 6 to 7, while downshifting has a bit of lag, upshifting takes forever and sometimes it doesn’t even ...