Unanswered Questions
34 questions with no upvoted or accepted answers
4
votes
0
answers
225
views
Sram AXS derailleur does not shift
Have you encountered a problem where a rear AXS derailleur stops shifting? Any suggestions?
I bought a mint 2023 GX AXS derailleur on Marketplace, it worked for the first short test ride on a road but ...
2
votes
0
answers
50
views
Something like chainsuck on RD lower pulley after new crankset install?
I just switched out a Shimano M5100 crankset for a SRAM GX Eagle crankset. I am using a KMC X11-EL chain. I cleaned the chain before installing it with the new crankset. My RD is a Shimano SLX 11-...
2
votes
1
answer
239
views
Upgrading Shimano Acera 8 speed Rear Derailleur to 8 speed Shimano XTR derailleur
Looking for some help here. I am upgrading Shimano Acera 8 speed rear derailleur to 8 speed Shimano XTR rear derailleur and it appears that because the old 8 speed XTR derailleur has a clip for the ...
2
votes
0
answers
59
views
clicking chain on 3rd gear only
Shimano DI2 11 speed XTR on my gravel bike. The 3rd from smallest gear on the cassette makes a clicking sound. Any other gear its fine. Cassette and chain are fairly new. Have reindexed, checked ...
2
votes
0
answers
416
views
Using 11-36t 9 speed derailleur with 11-40t 9 speed cassette
So I've got the shimano altus rd-m2000 and it says that it only supports 11-36t. However, I've seen people on forums say that it's possible with this derailleur. Even it I was wondering if with a ...
2
votes
0
answers
834
views
Why do SRAM rear derailleur not have a parallel movement
My SRAM rear derailleur (Rival 22 circa 2016) has a non parallel movement. When it is in the lowest gear, the cage and pulley sprockets align with the cassette sprockets, but when it's in the highest ...
1
vote
1
answer
38
views
Can a 37 total capacity setup do good with a 37 total capacity shortcage ss rear derailleur?
I've been asking this question for a few days now and I've been so curious about it
My setup is a 11-32t sprocket and a 50-34t crankset, the total of that is 37
The main question is in the title but ...
1
vote
0
answers
48
views
New tire tube and grinding noise?
I punctured my tire tube so i had to remove my back wheel out and replaced the tube, when reassembled, derailleurs started making grinding noises.
I checked where the sound was coming and it was ...
1
vote
0
answers
72
views
Not able to shift from a specific gear
I have a 9-speed rear derailleur and shifting from 1 to 9 isn’t a problem except when it is from 6 to 7, while downshifting has a bit of lag, upshifting takes forever and sometimes it doesn’t even ...
1
vote
0
answers
37
views
Compatibility Shimano rear derailleur RD-6300
I have this Shimano 600ax. Due to my stupidness I broke the body of the rear derailleur endings its life. There are other rear derailleurs (RD-6300) on ebay for example but these are very expensive ...
1
vote
0
answers
38
views
Chain goes slack in gear 5-10 and very noisey hum
When I’m coasting downhill >35 kph and chain is in gears 5-10 and I hit a bump the chain goes slack, a very loud irritating hum/vibration sound is emitted from the rear wheel until either I pedal ...
1
vote
0
answers
142
views
Chain creaks under pressure
Just adjusted my back derailleur and now the chain makes a loud creaking noise while under pressure. When on a repair stand the shifting is perfect but while biking it’s horrible and the sound & ...
1
vote
0
answers
176
views
Can i use claris R2000 rd on 14-34T mega range sprocket?
I have sprocket 14-34T with mega range. I planned to change my old (maybe 1990's) shimano tourney rd to shimano claris R2000 medium cage. Some of my local bike shop said that i can replace with claris ...
1
vote
0
answers
220
views
Direct mount rear derailleur
I'm upgrading an old MTB for commuting, it had a 5 speed on the back but I'm going to be putting on a new 26" rear wheel with a 7 speed cassette because the freewheel axle wobbles, makes noises ...
1
vote
0
answers
90
views
Campagnolo rear mech screw type
My limit screws' heads have gone rusty, I want to replace them for looks and to make sure they are easy to adjust on a ride. I would love hex rather than Philips heads!
Does anyone know the type of ...