Unanswered Questions
65 questions with no upvoted or accepted answers
6
votes
0
answers
110
views
What is forward drag on a coaster brake
I have a single-gear coaster brake bicycle that needed fixing. I would have to pedal real hard to get it to go and backpedal a block in advance for bike to stop. Very spongy brakes. Well I took brake ...
- 13.9k
2
votes
0
answers
47
views
Why have my rim brakes started making a scraping noise?
I bought a bike about 7 months ago, and I've noticed over the last few weeks that it's started making an unpleasant scraping noise when I brake. Does anyone know what might be causing this and how to ...
- 121
2
votes
1
answer
74
views
Sram/Avid brake hose compatiblity
I have Sram Rival AXS which I want to transfer from one bike to another. Unfortunately the new bike is bigger (M -> XL) so new brake hose is required. SRAM recommends SRAM Brake Hose Kit - Double ...
CommunityBot
- 1
2
votes
0
answers
96
views
Cable housing end cap for BR-M375
I replaced the no name brake calipers on an entry-level ebike for Shimano BR-M375. The cable housing for the rear caliper was a bit too long, so I cut off a few centimeters. Then, I put a new 5 mm end ...
- 4,159
2
votes
0
answers
284
views
after multiple brake bleed, lever's max stiffness is still close to bar
so after a few bleeds i've done on these Shimano saints, because of new levers replacement, i've found that the rear brake lever, although on max stiffness, goes way further to the bar then the other ...
- 185
2
votes
0
answers
178
views
SRAM Hydraulic brake stuck (with a changed bite point) after landing/impact
I experienced a weird problem on my SRAM level t 2 piston brakes.
I like hopping my bike around, e.g. bunny hopping onto curbs. Sometimes, if the impact is hard, the brake lever would have reduced ...
- 121
2
votes
0
answers
906
views
Normal MTB trigger shifters and hydraulic brake levers on a bullhorn handlebar
Was wondering if mounting Altus shifters and hydraulic brake levers on the vertical sides of a bullhorn handlebar would work or would be possible? I tried holding one of my grips on my flat bar while ...
- 75.8k
2
votes
0
answers
79
views
Asymmetric torque recommendation for bottom nut on damper side vs air side on a RockShox fork
I was doing lower leg service on my Recon Race solo air fork for the first time. According to the user manual from 2009 that came with the fork, bottom bolt (damper side) should be tightened with 6.8 ...
- 21
2
votes
0
answers
1k
views
Tightened the bolts on the bottom of my suspension fork -- What now?
So... a few hours ago I did a bolt check on my bike. As I was about finished I checked the 2 bolts on the bottom of each of the fork's legs. They were kinda easy to tighten so I said to myself go for ...
- 8,576
2
votes
0
answers
161
views
What kind of frame and brakes are these?
I just bought a bike and I can't figure out what kind of frame and brakes it has.
I found that the derailleurs were made by DNB Japan somewhere around 1960 and that the handlebar is french (Guidonn ...
- 128k
2
votes
0
answers
3k
views
Shimano Nexus 3 coaster brake screeching sound
When I brake hard/er with my Shimano Nexus 3 coaster brake it makes a loud screeching sound. Like really loud, everybody on the street would hear it and turn around. Since I know it's all internal all ...
- 352
2
votes
0
answers
707
views
Internal Roller Brake Problem
I have Shimano Inter M Roller Brakes on my bike. I felt the rear brakes were a bit light after riding 800 or so KM (total mileage on my bike so far) so I thought maybe theres a bit of cable stretch ...
- 115
2
votes
0
answers
90
views
Punctured fork seal
I accidentally punctured (very small hole) the dust seal on my Fox Evolution CTD fork. Obviously the seals capacity to prevent the dirt/dust/etc. from entering the forks has been compromised. Will any ...
CommunityBot
- 1
2
votes
1
answer
408
views
Is this a real Concorde or just a replica?
I'm confused with this, the lugs in this bike look identical with another Concorde but the tubing sticker clearly says "Reynolds". (Concorde only uses Colombus, right?)
2
votes
1
answer
174
views
Front Mountain Bike Cable Disk Brake Is Too Snappy on First Pull
When I grab my front disk brake for the first time on a ride after my bike has sat for a while it will buck me forward. Once it bucks me it works great. I have tried cleaning it with disc brake ...
