Unanswered Questions
68 questions with no upvoted or accepted answers
7
votes
1
answer
1k
views
Alternative to 5-speed twist shifter for Shimano Nexus 5-speed IGH?
I'm going to buy a SG-C7000-5D / SG-C7050-5D and don't want to use the twist shifter. Unfortunately there aren't many 5-speed flat bar shifters around theses days. I've searched for alfine shifters, ...
- 5,202
6
votes
0
answers
109
views
What is forward drag on a coaster brake
I have a single-gear coaster brake bicycle that needed fixing. I would have to pedal real hard to get it to go and backpedal a block in advance for bike to stop. Very spongy brakes. Well I took brake ...
- 13.9k
2
votes
0
answers
46
views
Why have my rim brakes started making a scraping noise?
I bought a bike about 7 months ago, and I've noticed over the last few weeks that it's started making an unpleasant scraping noise when I brake. Does anyone know what might be causing this and how to ...
- 121
2
votes
0
answers
33
views
How can I make my vintage sturmey Archer AW hub take a 3 speed cassette? (Minimal metal work, none if possible)
So to make answering my question easier, I'll start with the goals, I wish to be able to attach a 3 speed cassette and tensioner (relatively low cost) to my vintage Sturmey Archer AW hub so i can have ...
2
votes
0
answers
26
views
7 speed hub whistles
My 7 speed Nexus internal axle begins to whistle as speed increases, but noise stops when I slow down. Has nothing to do with the pedal crank.
- 5,202
2
votes
0
answers
53
views
Changing gear usage of Rohloff gears
I have a R&M Homage with Rohloff e-14 gears. I find I really just use gears 7 - 14. Can sprockets be changed so I would mainly use gears 4 - 11??
- 21
2
votes
1
answer
159
views
pedals only move bike at highest gear
Recently my bike will only move if I’m in the highest gear. I can pedal at lower gears but it will not move my bike forward at any reasonable speed and when I get up to even a very low speed the ...
CommunityBot
- 1
2
votes
1
answer
74
views
Sram/Avid brake hose compatiblity
I have Sram Rival AXS which I want to transfer from one bike to another. Unfortunately the new bike is bigger (M -> XL) so new brake hose is required. SRAM recommends SRAM Brake Hose Kit - Double ...
CommunityBot
- 1
2
votes
0
answers
183
views
Bicycle chain roller diameter size chart?
I'm digging for a while now, and can not find any helpful chart for chain roller diameters e.g. Shimano 8,9,10,11,12 speed. It differs of course depending on the manufacturer and the purpose. We know ...
- 153
2
votes
0
answers
95
views
Cable housing end cap for BR-M375
I replaced the no name brake calipers on an entry-level ebike for Shimano BR-M375. The cable housing for the rear caliper was a bit too long, so I cut off a few centimeters. Then, I put a new 5 mm end ...
- 4,159
2
votes
0
answers
133
views
U.S. source for Alfine 11 oil for oil changes?
Yesterday I changed the oil in my Alfine 11-speed hub. I bought the 50ml bottle of SG-S700 from an eBay seller in Florida, the last one in the site's search results originating from the United States. ...
- 639
2
votes
0
answers
284
views
after multiple brake bleed, lever's max stiffness is still close to bar
so after a few bleeds i've done on these Shimano saints, because of new levers replacement, i've found that the rear brake lever, although on max stiffness, goes way further to the bar then the other ...
- 185
2
votes
0
answers
232
views
Does (or has in the past) an adaptor existed to mount a disc rotor to a Shimano Rollerbrake type hub?
I have acquired a Nexus 8speed rear hub. It’s a good one and I’d love to use it. However, it has been set up to use rim brakes and under the plastic cover is the interface to mount a rollerbrake. Does ...
- 14.6k
2
votes
0
answers
156
views
Why is my Sturmey-Archer 5-speed hub sticking between 1st and 2nd gear?
I've been trying to set up a Sturmey-Archer X-RD5 (W) hub to no avail. I can get it moving between 2nd and 5th gears just fine, but as soon as I pull it into 1st the indicator rod (and I assume ...
- 173
2
votes
0
answers
177
views
SRAM Hydraulic brake stuck (with a changed bite point) after landing/impact
I experienced a weird problem on my SRAM level t 2 piston brakes.
I like hopping my bike around, e.g. bunny hopping onto curbs. Sometimes, if the impact is hard, the brake lever would have reduced ...
- 121