Unanswered Questions
72 questions with no upvoted or accepted answers
9
votes
1
answer
950
views
Shimano Dura-Ace R9120 lever leaking
My bike's Dura-Ace R9120 rear-brake/front derailleur shifter (left shifter in UK) leaks brake fluid when I pull hard on the lever. It leaks from this specific place:
I understand this lever is ...
CommunityBot
- 1
6
votes
0
answers
109
views
What is forward drag on a coaster brake
I have a single-gear coaster brake bicycle that needed fixing. I would have to pedal real hard to get it to go and backpedal a block in advance for bike to stop. Very spongy brakes. Well I took brake ...
- 13.9k
6
votes
0
answers
483
views
Shimano road bike lever leaking mineral oil
I have a leak in my Shimano DA 9170 (right) shifter. When I do a bleed, everything seems to work for a ride or two and then I start to lose braking power and the underside of the brake hood is wet ...
CommunityBot
- 1
3
votes
0
answers
52
views
Microshift AdventX drop bar lever spring position
My left brake lever spring was not pulling the lever back and I checked and it was bent. I removed the lever and fixed the spring, but I don't know how to put it back. I can't find any tutorials nor ...
- 173
2
votes
1
answer
26
views
Replacing brake lever on Shimano Nexus integrated shifter/brake lever
I have a Shimano Nexus Revoshift shifter with brake lever, part number SB-C6000-8, to use with a Nexus 8 internally geared hub. The brake lever has been sheared off where it joins the body of the ...
- 135
2
votes
0
answers
46
views
Why have my rim brakes started making a scraping noise?
I bought a bike about 7 months ago, and I've noticed over the last few weeks that it's started making an unpleasant scraping noise when I brake. Does anyone know what might be causing this and how to ...
- 121
2
votes
1
answer
74
views
Sram/Avid brake hose compatiblity
I have Sram Rival AXS which I want to transfer from one bike to another. Unfortunately the new bike is bigger (M -> XL) so new brake hose is required. SRAM recommends SRAM Brake Hose Kit - Double ...
CommunityBot
- 1
2
votes
0
answers
95
views
Cable housing end cap for BR-M375
I replaced the no name brake calipers on an entry-level ebike for Shimano BR-M375. The cable housing for the rear caliper was a bit too long, so I cut off a few centimeters. Then, I put a new 5 mm end ...
- 4,159
2
votes
0
answers
284
views
after multiple brake bleed, lever's max stiffness is still close to bar
so after a few bleeds i've done on these Shimano saints, because of new levers replacement, i've found that the rear brake lever, although on max stiffness, goes way further to the bar then the other ...
- 185
2
votes
0
answers
177
views
SRAM Hydraulic brake stuck (with a changed bite point) after landing/impact
I experienced a weird problem on my SRAM level t 2 piston brakes.
I like hopping my bike around, e.g. bunny hopping onto curbs. Sometimes, if the impact is hard, the brake lever would have reduced ...
- 121
2
votes
0
answers
514
views
Cane Creek "universal" hoods and Shimano 600 (BL-6400) lever compatibility
Does anyone happen to know know if these Cane Creek "universal" hoods are compatible with these vintage Shimano 600 (BL-6400) levers?
It's okay if they don't fit quite perfectly or if I have ...
- 128k
2
votes
0
answers
905
views
Normal MTB trigger shifters and hydraulic brake levers on a bullhorn handlebar
Was wondering if mounting Altus shifters and hydraulic brake levers on the vertical sides of a bullhorn handlebar would work or would be possible? I tried holding one of my grips on my flat bar while ...
- 75.8k
2
votes
0
answers
83
views
Brake levers for non-cycling application
I would like to purchase and install 2-finger brake levers to operate the diff-lock and brake on a walk-behind garden tractor. Okay, it's not a bike but it is a two-wheeled vehicle. The most ...
- 233
2
votes
0
answers
79
views
Asymmetric torque recommendation for bottom nut on damper side vs air side on a RockShox fork
I was doing lower leg service on my Recon Race solo air fork for the first time. According to the user manual from 2009 that came with the fork, bottom bolt (damper side) should be tightened with 6.8 ...
- 21
2
votes
0
answers
1k
views
Tightened the bolts on the bottom of my suspension fork -- What now?
So... a few hours ago I did a bolt check on my bike. As I was about finished I checked the 2 bolts on the bottom of each of the fork's legs. They were kinda easy to tighten so I said to myself go for ...
- 8,576