Unanswered Questions
23 questions with no upvoted or accepted answers
7
votes
0
answers
194
views
Marlin 2.0 Firmware temperature jumping on LCD when trying to configure UBL
Flashed Marlin 2.0 on my Folgertech 2020 Prusa i3 variant.
Calibrating seems to have gone smoothly until I tried to set up UBL.
Saved the mesh into EEPROM with the ...
4
votes
0
answers
77
views
What does CRASH_RECOVER mean from Octoprint?
When watching the Raspberry PI daemon.log while running OctoPrint, I see contents like the following, which occasionally includes enqueing "CRASH_RECOVER" (but I do not see "...
2
votes
0
answers
23
views
How to polish heatbreak surface?
I have a plastic squeezing up from the heatbreak thread. This indicates improper seal, but I have screwed everything together tightly. After disassembly, I realized I have a scuffed surface on my ...
2
votes
0
answers
129
views
Weird infill edge problem
I'm having this weird issue; for some weird reason, the infill pattern starts separating from the walls and over time, the print becomes a mess. As it separates, it starts to curve, and you get this ...
2
votes
0
answers
145
views
Prusa MK3S Nylon&ABS print failures
I'm using Prusa i3 MK3S and every time I want to create a durable, impact resistant part, I use ABS/Nylon. The problem is, however, that when I print something small (of less than 1 cm width for ...
2
votes
0
answers
676
views
Geeetech Prusa I3 Pro W. Cannot update firmware
Initially when I built it, it turned on and the LCD worked. I had an issue with the Z axis but I think that's unrelated to my current issue.
The next day when powering on the LCD just showed black ...
2
votes
0
answers
3k
views
Where is .dxf file of this frame(Prusa i3)?
I am looking for this fram, but in github there is no download option for it!
So I did copy the code and paste it, but in result when I measure the big frame's edges it shows bigger 9100mm !! but I ...
1
vote
0
answers
62
views
What issue can make very short temperature spikes to appear?
I have issues with momentarily temperature spikes, but only above 250 °C. At and below 250 °C it's pretty solid.
I'm using Prusa MK3s+ with a E3D Revo upgrade.
I suspected connector issues as ...
1
vote
0
answers
25
views
Prusa I3 MK2s with tilt in the X and Y directions
So I converted my Prusa MK2S to use Duet electronics. I have always had problems with bed leveling. It doesn't appear to help much if any.
So I can complete a bed probing session but the result is ...
1
vote
0
answers
108
views
Horrid issues with printing with Anet A6?8?
I just recently got a printer, supposed to be a Prusa i3 Reprap clone. It came with Repetier firmware on it, and its previous owner had no idea about any calibration. I calibrated X-, Y-, and Z-axis ...
1
vote
0
answers
105
views
Print quality ruined after firmware update i3 mk3
I'll try to give as much detail as I know here but let me know if there is anything missing.
I have a Prusa i3 MK3 that I got in about 2018 and it was working perfectly fine. Print quality was pretty ...
1
vote
0
answers
55
views
ETA for print job showing negative in Repetier host
I'm using Repetier host 1.0.6, and ever since adding default retraction settings, the "ETA" showing during a print job is negative:
It stays this way throughout the print job, which is no fun, since ...
1
vote
0
answers
74
views
Steps to setup a new 3D Printer
I hope it doesn't get closed since my question is widely open:
I got recently a Geeetech Prusa i3 Pro B as a DIY kit, the assembly took a lot of time since the package did not include a building ...
1
vote
0
answers
426
views
Prusa i3 Linux Mint Slic3r install problem
New to this domain, I got my prusa i3 last week and finished assemblage. Repetier params in Linux Mint 18 are ok too.
I'm now trying to launch slic3r for the first time but I got this error launching ...
0
votes
0
answers
20
views
3D printer X-axis sometimes binds up whilst printing
My MK2s has developed a strange problem where the X-axis will bind up whilst printing. This causes it to layer shift. The strange thing is I can move the X-axis manually. It doesn't bind up and feels ...