All Questions
Tagged with networking linux
4,766
questions
1
vote
1
answer
27
views
10 gig PCIe network card won't come up unless onboard 2.5 gig card is connected
I recently acquired a zimacube - its a N100 based NAS system. I've wiped the preinstalled zimaos and run a minimal install of ubuntu server 24.04 and made the usual changes I do on my builds for ...
0
votes
2
answers
20
views
How to setup a reverse proxy across multiple devices on a local network
I am very new to setting up servers and network management so please bear with me.
I have multiple devices on which I would like to self host different services. This includes a few RPI5 and another ...
0
votes
0
answers
32
views
100Mbps-1000Mbps NICs all limited to ~40Mbps?
I have paid for 1000Mbps for quite some time from my ISP and have always had trouble with it maxing out at ~40Mbps. I always faulted my VPN and just suffered through it.
I finally tried to ...
0
votes
0
answers
14
views
How do I configure 2 public IP addresses on Debian and enable NAT traversal on one?
I got 2 IP addresses from my hosting company, xx.xx.xx.109 and xx.xx.xx.110, both in the same subnet. The subnet mask is 255.255.255.192 and the gateway is xx.xx.xx.20
I have a Proxmox server and ...
0
votes
0
answers
13
views
How do you set up a system wide Proxy system for multiple SSH Dynamic Port (SOCKS5) Connections
What I'm trying to do is create a FoxyProxy type system wide proxy system for SSH Dynamic ports. My starting point is a OpenBSD Unix Based system, but has a lot of RedHat based additions. All of the ...
1
vote
0
answers
19
views
Hotspot connection SSH / Ping
I have a singleboard computer (Rock 4 SE) with a wifi that is hotspot capable. It is running linux Debian. I want to SSH into it with my laptop using the linux machines own wifi as a hotspot for ...
0
votes
0
answers
32
views
How to pull NMEA0183 traffic from a TCP-based "talker" and send it to a UDP-based listener?
I have one machine (192.168.11.100) that acts as an NMEA0183 "talker" via port 10110/TCP and I have another machine (let's say 192.168.11.110) that can only receive the NMEA strings it needs ...
0
votes
1
answer
12
views
Docker Compose network isolation mechanism in Linux
When I deploy Docker Compose services, I found that the Docker containers are all on one bridged linux segment; this much is expected. However, sometimes I have had problems connecting from one linux ...
0
votes
2
answers
58
views
One-to-one NAT on Windows 10
I have three computers:
Host A: Linux PC, with IP 192.168.1.50/24
Host B: Windows VM running on Host A, with IP 192.168.1.100/24 (host-only network) and 192.168.2.100 (vpn)
Host C: PC with any OS (...
0
votes
1
answer
52
views
Linux Docker compose container cannot ping another bridged Docker container
Overview
I need a Docker Compose zabbix host to ping a host on a containerlab docker network.
These two Docker networks run under a linux Docker host machine as below... This information comes from ...
0
votes
0
answers
48
views
No available connections in WSL2 + Ubuntu + KDE
I use:
Windows 10 Pro (ver. 22H2 19045.4529)
WSL2 (wsl --set-default-version 2)
Ubuntu 22.04
KDE Plasma 5.24.7 (sudo apt install kde-plasma-desktop)
Kernel 5.15.153.1-microsoft-standard-WSL2 (64-bit)
...
1
vote
0
answers
28
views
Linux - Preserve client IP Addresses when connecting to game server over wireguard VPN tunnel from VPS
My question is almost perfectly summarised here:
Preserve connecting clients IP address through an OpenVPN tunnel
And the solution provided in that post hints at what I need to do, and have been ...
0
votes
0
answers
15
views
Server sometimes not sending ACK in response to PSH, ACK
We've implemented a TCP server socket in C++ on a linux machine which is connected to another device, streaming data small packets at high rate (800 Hz). To do so without too much latency (which we ...
0
votes
1
answer
24
views
Basic kea-dhcp4 server setup failure, likely caused by wrong config file
Setup
Intended setup:
<router>----ethernet cable ---<linux PC>
Router IP: 192.168.1.1
(DHCP relay, DHCP Server IP: 192.168.1.2)
Linux PC (hosting the server) Static IP: 192.168.1.2
OS: ...
1
vote
1
answer
63
views
How can I setup FIREWALLD with IPSEC (StrongSwan) Site-to-Site to make PING work on Debian 12?
I have 3 nodes with public and local IP address, each:
Node A: edge router #1 (10.41.1.0/24)
Node B: edge router #2 (10.48.2.0/24)
Node C: VMS with Debian 12, docker containers and firewalld (ex. 172....