All Questions
60
questions
2
votes
0
answers
110
views
Mounting External Intel Raid Device on Linux Failing, No Suitable Superblock and Read Past End
I have a hard-disk from a dead machine that I'm trying to mount on my Linux machine. For reference, I'm using Fedora 39 and mdadm v4.2. First, I tried just mounting it, correctly showing it's a RAID ...
- 221
0
votes
0
answers
173
views
Raid 10 gone - how to rebuild / find informations
Because of another task, i had to disconnect all the raid hdd's from my pc.
Shutdown -> disconnect hdd's -> boot -> shutdown -> connect hdd's -> boot -> raid completely lost.
mdadm --...
- 101
0
votes
2
answers
3k
views
How to restore my RAID5 after mistakenly failing one of the drives?
I have a RAID5 on Xubuntu 20.04, created with mdadm. I failed one of the three drives by mistake. The array is still working, but I get errors or responses I do not understand from my attempts to ...
- 183
0
votes
1
answer
184
views
raid 4 3 disks + 2 parity disks
I have a raid 0 with 3 disks and I want to be able to lose some disks without losing data.
I'm using mdadm and I already started to grow my config
Current config:
Personalities : [raid0] [linear] [...
- 13
1
vote
1
answer
129
views
My Software RAID 5 has 4 3TB HDDs, now two of them have bad sectors. What is a good way to replace them?
I run mdadm on Ubuntu 18.04 to build a RAID 5 array of 4 3TB drives several years ago. The machine was not running for years. Yesterday I powered it on and found two of the disks have a bunch of bad ...
- 123
0
votes
1
answer
218
views
How to reshape a 2-disk RAID1 into a 2-disk RAID5 using mdadm?
According to How to remove a drive from a non-standard 2-drive RAID 5 array?, "with mdadm, a 2 drive RAID 5 is binary identical to a RAID1". If that is so, what's the mdadm command line for ...
- 105
1
vote
1
answer
169
views
How long should RAID 10 syncing stay at 'recovery = 99.9%'?
After replacing a faulty disk in a (CentOS 7) RAID 10, the syncing is at the following stage for quite some time now; it has had this state for more than a day:
md10 : active raid10 sdp1[9] sdo1[8](S)...
- 1,153
1
vote
1
answer
616
views
Way to monitor progress of RAID10 rebuilding disks, when RAID does not show in /proc/mdstat?
I have an inactive RAID 10, and the output of mdadm --assemble --scan -v |& tail -17 is:
mdadm: /dev/sdn1 is identified as a member of /dev/md/10, slot 5.
mdadm: /dev/sdk1 is identified as a ...
- 1,153
1
vote
2
answers
2k
views
mdadm - Raid 1 arrays do not assemble after reboot
I rebooted my server after creating 3 raid 1 arrays with mdadm, and after rebooting, systemd was spitting out errors about the raid devices timing out when trying to assemble them at boot.
I was given ...
- 2,984
0
votes
1
answer
576
views
What does delta devices of the mdadm--detail output mean?
Here is an output of mdadm --detail:
$ mdadm -D /dev/md2
/dev/md2:
Version : 1.2
Creation Time : Wed Jun 24 16:41:17 2020
Raid Level : raid5
Array Size : 7809195456 (7447.43 GiB ...
- 123
1
vote
3
answers
1k
views
Disable warning from mdadm for “degraded” RAID1 with missing drive
I recently had a server outage due to a failed drive. Because of that I set up the server with a new SSD in RAID1 this time but until I managed to get another SSD drive the mdadm-based RAID1 runs with ...
- 845
0
votes
1
answer
387
views
Long-term local offline RAID storage of never-changing data
I have about 20TB of data that will remain unchanged (forever) and I am planning to make offline copies with a little redundancy.
I already have a lot of 2TB drives that I plan on using and I am ...
3
votes
0
answers
3k
views
Synology DiskStation: How to stop/interrupt a running reshape (RAID5 -> RAID6)
The short of it: I have a running reshape from RAID5 with 5 disks to RAID6 with 6 disks which needs to be stopped, so I can power off the system. I do not care if the reshape needs to start fresh once ...
- 86
1
vote
1
answer
741
views
btrfs ontop of mdadm raid - calculating stripes for corrupt sectors for use with raid6check
I've got a setup with btrfs running on top of mdadm raid6 as btrfs's RAID5/6 code isn't stable yet. I figured this way I'd get the benefits of snapshotting and checksumming with a few extra hoops to ...
- 41
2
votes
1
answer
3k
views
mdadm shows inactive raid0 array instead of degraded raid6 after disk failure
I've been running an Ubuntu 18.04 system with an 8-disk raid 6 array, that crashed while having a faulty disk (I only noticed that there was a faulty disk after the crash). The raid array has survived ...
- 21