All Questions
Tagged with kali-linux networking
102
questions
0
votes
0
answers
20
views
Victim loses internet connection during arp spoofing against it
The point is as follows.
VirtualBox is installed on my laptop. It has a Kali Linux virtual machine installed with which I want to perform ARP spoofing on my phone.
In the Kali Linux network settings, ...
0
votes
0
answers
18
views
Kali does not detect Eth1 - VMware Pro
Working on an assignment where I need to create a new network adaptor (Host only) in VMware an I need to enter the following
sudo ifconfig eth0 down
sudo ifconfig eth1 192.168.150.129 netmask 255.255....
0
votes
0
answers
122
views
Cannot ping windows from kali linux laptop
In general, I can ping from windows 11 kali linux mine on a second laptop, ping 192.168.1.84 but when I try to ping ping 192.168.1.51 from kali linux there is no response and the ping hangs. Two ...
2
votes
1
answer
53
views
Full Network Enumeration without an assigned ip address
I've faced a situation where I connected to a network with an ethernet cable and the DHCP server was disabled, so I didn't get an assigned ip. I was wondering if I can run a scan with kali linux tools ...
0
votes
0
answers
97
views
how to make my vm reachable from hosts within same network
Context:
I want to do a reverse shell POC, so I am using Kali Linux on virtual box hosted on a Windows machine. On the same network my Windows machine hosted, there is a Linux machine that I want to ...
0
votes
0
answers
130
views
How can I collect packets on 5165 MHz frequency?
I have an Intel AX210 Wifi 6E supported wireless card.
There is a device that broadcasts WIFI on the 5165 MHz frequency.
For my cyber security research, I need to collect packets from this device ...
1
vote
0
answers
83
views
kali linux filter by protocol wireshark's pcaps
I spent the last 2h looking for a way to quikly filter pcaps, it seems that it is possible using cmd/bat on windows but I can't find anything for kali linux.
I have a way too big pcap and I want to ...
0
votes
1
answer
260
views
Unstable Wifi Detection in Virtual Box
I managed to install drivers for my Wifi adapter and VM Linux (virtual box) manages to recognize it as wlan0, however if it NEVER shows avaiable networks, which there are.
I've gone and reinstalled ...
1
vote
0
answers
182
views
OpenVPN can't open (Kali)
I'm setting up an OpenVPN server on Kali. When the service is started, this error occurs:
Job for [email protected] failed because the control process exited with error code. See "...
0
votes
1
answer
885
views
There is no bettercap file in the file system
I downloaded bettercap by using this command sudo apt install bettercap but when I go to this location /usr/share/ I don't find any folder named bettercap and there's no caplets folder
0
votes
0
answers
1k
views
DNSChef practice, "communications error to 127.0.0.1#53: connection refused"
In Kali Linux, I face an issue while trying to implement/practice DNSChef on my VirtualBox, following the description here.
For:
host -t A thesprawl.org
I get:
;; communications error to 127.0.0.1#...
1
vote
0
answers
136
views
Kali Linux takes way too long to load the GUI after entering the password? IPTABLES
After entering the passward to login, it takes way too long to load GUI.
I think the issue is with the firewall, when I enable it the GUI loads way two long to load. More than a minute, if it's ...
0
votes
0
answers
405
views
Netcat connection not working both ways (Mac-Kali), connection refused
I was following this website in order to establish a netcat connection. I have a mac and a kali virtual machine. If from my mac I type nc -lv 1234 and from kali I type nc ip.of.my.mac 1234 then the ...
0
votes
0
answers
61
views
Connect Mac to raspi4(kali) via direct ssh
Is there a way to connect to a Raspberry Pi 4 with kali linux ARM via Direct SSH, without any other network or router set up?
I have set up a little raspi4 with kali linux (latest version atm.). I ...
0
votes
0
answers
3k
views
Host is up. All 1000 scanned ports on ***.***.**.* are in ignored states. Not shown: 1000 filtered tcp ports (no-response)
I am trying to scan an ip address using nmap using the command:
sudo nmap -A ***.***.*.*
and I get this as a result
Host is up.
All 1000 scanned ports on ***.***.**.* are in ignored states.
Not shown:...